Electronic Components Kit for Arduino UNO Mega Kit electronic components for Arduino UNO Mega.It allows to build various projects of various complexity, from the easiest ... to the most complicatedThe elements are placed in the box to keep everything in order. Characteristic: It includes the following module references: - 1x Protoboard Breadbord 400 points Arduino- 20x Male-Male Cables 20cm Jumpers Dupont 2,54- 1x LED Diode Assortment Kit 30 pcs 5mm red, green, yellow- Resistors: - 10x Resistors 200R Ohm 5% 0,25W 1/4W - 10x Resistors 1K Ohm 5% 0,25W 1/4W - 10x Resistors 10K Ohm 5% 0,25W 1/4W - 10x Resistors 100K Ohm 5% 0,25W 1/4W- 2x Photoresistor GL5516 LDR- Push switch buttons: - 1x Push Switch Button B3F Omron Blue Key 12mm Code B0039 Available Price €11.14
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.99
Shield Sensor Expansion Board Arduino compatible V2.0 Arduino Shield Sensor Expansion Board V2.0 features: The Mega Sensor Shield V2.0 allows: - To be directly punched to an Arduino Uno, Mega, Leonardo board - Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more - Size: 100x54x12 mm Code M0129 ✗ Out-of-Stock Regular price €3.89 -€0.90 Price €2.99
Electronic Components Kit TIP120 for Arduino check it Contenido:- 20x Cable macho-macho 20cm - 10x Cable hembra-macho 20cm - Kit de diodos LED - 20 unidades ( 5x rojo, 5x verde, 5x amarillo, 5x blanco) Resistencias:- 220R- 10 unidades- 10k- 5 unidades- 1k- 5 unidades- Transistor TIP120 TO-220 - 1 unidad- Diodo LED RGB - 1 unidad- Condensador electrolítico 470uF/50V - 2 unidades check it Content:- Prototype plate 400 points- 20x Cable Jumper mach-macho- LED diode kit - 30 units (10x red, 10x green, 10x yellow) Resistances:- 100k- 10 units- 10k- 10 units- 1k- 10 units- 220R- 10 units- Photoresistor GL5516 Type LDR 10k - 2 units- Push buttons Omron B3F Blue, Red, White - 3 units- 100uF / 50V electrolytic capacitor - 5 units Code B0100 Available Price €5.99
Vertical Liquid Level Sensor Switch Level sensor for liquids with float. The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums. Characteristic: - Maximum Load: 50W - Maximum Switching Voltage: 250V - Maximum Switching Current: 0.5A - Maximum charging current: 1A - Operating temperature: -10ºC to + 60ºC - Size: 58mm x 18mm Code S0043 Available Price €2.95
Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features: - 1 logical step of the input voltage VD: 5 VDC- Control of the input voltage VS and control by pulse width modulation: - VIN input: 6 - 12 VDC - PWRIN input: 4.8 - 35 VDC- Logic current flow: Iss <36m A- Operation current management: Io <2 A- Maximum power dissipation 25W (T = 75 ° C)- Input of the control signal: Code M0136 Available Regular price €11.50 -€1.51 Price €9.99
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Available Regular price €8.95 -€4.00 Price €4.95
Screw Shield V2 for Arduino UNO Screw Shield V2- Arduino ScrewShield UNO features: Screw Shield V2 allows: - Being punctured directly to an Arduino Uno- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0172 Available Regular price €4.95 -€1.00 Price €3.95
DS18B20 Waterproof Digital Temperature Sensor Probe 3m Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 ° C to 125 ° C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 3m Code S0008 ✗ Out-of-Stock Price €4.85
Kit 37 Sensors in a Box for Arduino The perfect Arduino sensor kit to start learning about the world of electronics with Arduino. It comes with our step-by-step guide to each sensor, as well as its libraries. Code B0040 Available Price €19.49
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €9.90
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
Screw Shield V1 for Arduino UNO y MEGA Screw Shield V1- Arduino ScrewShield UNO y MEGA features: Screw Shield V1 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0173 Available Price €3.95
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €3.15 -€0.50 Price €2.65
M18 Inductive Proximity Sensor M18 Inductive Proximity Sensor features: - Inductive proximity sensor detection switch LJ18A3-8-Z / BX - NPN DC6-36V - A Often used for 3D printer bed leveling - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open ) - Detecting distance 8mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition) - Head diameter 18 mm - Size 6.9 x 2cm - Cable length 90cm Code S0042 Available Price €3.49
Arduino Starter Kit Classroom Pack The ideal package for teachers looking for classroom solutions that introduce programming and electronics through fun and engaging interactive projects. It is a ready-made package with the curriculum available for ready-made classes - it comes with a booklet of 15 introduction classes written by Arduino team. The Arduino Starter Kit class package is a solution package, containing six of the popular Arduino Starter Kits. This classroom package is for a classroom of at least twelve students - the recommended ratio is two students per kit - and is intended for use by middle school teachers looking for a comprehensive educational solution based on the Arduino platform. Code KA007 Last items in stock Price €599.00
Arduino Kit Starter Oficial Arduino Starter Kit is a perfect kit to start your adventure with Arduino. It offers a range of original components, which ensure compatibility with all Arduino parts and give you access to full range of official materials. Additionally, you get a 15 projects booklet, which is pretty much all you need to start rolling with your Arduino projects Code KA002 Available Price €105.95
ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Mega2560 V3.0 ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Mega2560 V3.0 features: - To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Mega2560, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip- The seamless mini breadboard has 170 connection points.- You can stick on the shield with its self-adhesive back. Code M0204 Available Regular price €3.19 -€0.30 Price €2.89
MQ-3 Alcohol Sensor Module Ethanol Breathalyzer Ethanol alcohol sensor module.MQ gas sensor uses a small indoor heater with an electrochemical sensor.When the alcohol molecules in the air comply with the electrode the ethanol "changes" into acetic acid and then more current is produced.MQ-3 Alcohol Sensor Module Ethanol Breathalyzer features:- Main chip: alcohol sensor MQ-3 and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Detection concentration:- 0.05mg/L - 10mg/L- Quick response features:- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0009 Available Price €2.95
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
Arduino Oplà IoT Kit - Spanish - Official Internet of Things Kit This new official Arduino Stuff online starter kit is the perfect kit to start your adventure with Arduino. It offers everything you need to introduce your home or environment to the world of home automation and Smart Home. This programmable platform consists of various sensors, touch buttons, actuators, and even a screen, all embedded inside a sophisticated spherical housing, allowing you to add smart connectivity to your devices. The 8 projects included in the Oplà IoT Kit allow users to turn everyday devices into intelligent devices, which can be remotely controlled from a mobile phone. Code AKX26 Last items in stock Price €145.90
8 Channel High Trip 5V 10A Relay Module This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, from the TTL 8 Channel High Trip 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage Vcc: 5Vdc - Output Current: 10A - High trip min 3.3V input IN1. ..IN8 - Relay activation current: 5 ~ 10mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 55x 139mm - Weight: 120g COM GND jumper input: connects GND optocouplers and GND of the circuit Code RL015 Available Price €9.95
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €21.99
DHT22/AM2302 Temperature Humidity Sensor The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features: - Voltage Operating: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Code S0018 Available Price €3.95
DS18B20 Temperature Sensor 0.5ºC TO-92 Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:- Device function: Temperature sensor- Type of output: Digital- Supply voltage: 3V to 5.5V- Accuracy: ± 0.5ºC- Temperature threshold: Programmable- Operating temperature: -55ºC to + 125ºC- Encapsulated: TO-92- Supply current: 1.5mA Code S0014 Available Price €1.95
TinkerKit Braccio Robot Arduino - Robot Arm 6 DOF The Tinkerkit Braccio Robot, is a fully operational and functional robot arm, with 6 degrees of freedom, easily controlled through Arduino. It can be assembled in different ways to use it in the applications that are required, such as moving objects, connecting a camera or a solar panel. Discover the unlimited potential of robotics and mechanics with BRACCIO! Code T050000 Available Regular price €286.49 -€30.00 Price €256.49
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.59
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €23.99
WS2812 RGB 5050 Smart Addressable 5V Arduino compatible LED WS2811 WS2812 RGB 5050 Smart Addressable 5V Arduino LED WS2811 features: - WS2812 are LEDs that have built-in logic, making it possible to vary the color of each LED individually - WS2812 includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are individually indexable. - They are based on the 5050 LED - 24-bit color control (8-bit PWM per channel) - 16.8 millions of colors per LED - One-wire communication - Power: max. 5 Vdc - Current: 18.5mA - Input and output terminals (data and power) Code P0102 Available Price €1.69
Precision Temperature Sensor TO-92 LM335 LM335Z-ST Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:- Power supply from 5 to 30 Vdc- Connection through analog input- Temperature range from -40ºC to 100ºC- Linearity +10 mV / ºK- Accuracy of measurement: ± 2 ° C- Manufacturer: Texas Instruments Code S0120 Available Price €3.99
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
Qwiic cable protoboard - 4 pin This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme: Code SP020 Available Price €1.99
Kit Funduino I/O Expansion starter kit for Arduino UNO Kit Funduino I / O Expansion starter kit for Arduino UNO R3.Kit 37 Sensors in a Box for Arduino features: Including the referencias of módulos siguientes: - 1x módulo Funduino I / O Expansion- 1x módulo zumbador activo Keyes- 1x módulo foto resistencia Keyes- 1x módulo sensor of temperatura Keyes- 4x módulos sensor LED sombrero of Keyes paja- 1x módulo sensor of sonido Keyes- 1x módulo sensor Rotation Keyes- 1x pulsador módulo- 1x distancia sensor HC-SR04- 1x módulo Joystick Doble 2 Ejes XY- 1x servo 9g SG90- 9x Dupont cables con conector 3 pins- 20x Hembra-Macho Cables 20cm- 1x USB cable for Arduino UNO Tipo A-B 50cm Helpful Links:Install the IDE Arduino development interface Code B0056 Available Price €38.90
Qwiic cable 50mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long Code SP040 Available Price €1.19
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €4.46
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
DS18B20 Probe 2m Submersible Temperature Sensor Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 2m Code S0015 Available Price €3.79
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
Makey Makey Classic Contents Makey Makey Board USB Cable 7 Alligator Clips 6 Connector Wires Instructions with Visual Project Start Guide Online Documentation 20 Color Stickers Start out easy with a banana piano. First setup takes seconds. Then make games controllers, musical instruments, and countless inventions. Advance to additional inputs and multi-key remapping up to 18 keys.Turn everyday objects like bananas into touchpads! Connect the world around you to your computer! Setup takes just seconds. Just plug, clip, and play! No programing knowledge needed. No software to install. Works with Mac and Windows.1000s of possibilities! Draw your own game controller, sneak a cat selfie, and dance like never before.Ages 8 to infinity. Code B0101 Last items in stock Price €69.95
SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.99
LM35DZ Temperature Sensor TO-92 LM35 Temperature Sensor LM35DZ TO92 features:- The output is linear and each degree Celsius equals 10 mV- Power supply from 4 to 30 Vdc- Connection through analog input- Temperature range from 0ºC to 100ºC- Linearity +10 mV / ºC- Quantity: 1 unit Code S0016 Available Price €2.49
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features: - Adjustable High Sensitivity Acoustic Sensor - LM393 comparator chip - Integrated indicator LED - AO analog output, output voltage signal in time real microphone - DO digital output, sensitivity adjustable through potentiometer - Frequency Range between 30 and 15000 Hz - Power 4 ~ 6V - Measurements 36x16x15mm Code S0017 Available Price €1.79
Relay SRD-05 DC-2P 5V 10A SPDT - SRD-05VDC-SL-C Relay SRD-05 DC-2P 5V 10A SPDT features:- Supply voltage: 5V- Output Current: 10A- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica Code RL011 Available Price €0.69
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
Kit Mega XXL Darwin for Arduino Perfect "Mega XXL Darwin Kit" to learn programming and electronics with Arduino. It allows you to build various projects of varying complexity, from the easiest... to the most complicated. The elements are placed in the box to keep everything in order. Code B0071 Available Price €53.99
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.79
5.8GHz Doppler Radar Motion Sensor 5.8GHz Doppler Radar Motion Sensor features: - Microwave motion detector module - The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications. - High resistance to radio-frequency interference - Frequency: 5.8GHz - Operating Voltage: 3.3V - 20V TTL 3.3V - Standby Current: 3mA - Detection Range: 3-8 meters, 360 degrees - Power of Output: 2mW - Dimensions: 32x23 mm - R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k - R9 - for sensitivity adjustment Code M0112 ✗ Out-of-Stock Price €4.46
Arduino PORTENTA Breakout Board The Portenta Breakout module extends the capabilities of the Arduino Portenta module with additional connectors and cables. The module includes a power switch, a DIP switch for selecting the start mode of the Arduino Portenta, as well as a series of connectors: USB A, RJ5, microSD, OpenMW, MIPI 20T JTAG. The board also includes the RTC chip, as well as a slot for the CR2032 battery, a screw connector for the power supply and all the cables for the Arduino Portenta module. Code ASX00031 Available Regular price €54.95 -€4.96 Price €49.99
Relay SRD-12 DC-2P 12V 10A SPDT Relay SRD-12 DC-2P 12V 10A SPDT features:- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- For power switching with 12V DC signals - Microcontroller, Arduino, Electronica Code RL012 Available Price €0.98
Current Sensor ACS712 AC/DC 30A for Arduino Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 30A - Dimensions: 31 x 13 mm Code M0028 Available Price €3.39
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.99
DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 Available Price €2.49
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€2.00 Price €4.49
Kit XXL Sensors for Arduino compatible Perfect "Kit XXL Sensors" to learn programming with Arduino, the basis of electronics. It allows to build various projects of various complexity, from the easiest ... to the most complicated. The elements are placed in the box to keep everything in order. The kit does not include an Arduino board. An original Arduino board or a Chinese equivalent can be purchased separately. Code B0115 Available Regular price €60.29 -€17.70 Price €42.59
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.89
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.49
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.99 -€0.50 Price €3.49
Starter Kit XL Arduino compatible Perfect kit to learn programming in the middle of Arduino the basic of electronics It allows to build various projects of various complexity, from the easiest ... to the most complicated.The elements are placed in the box to keep everything in order. The kit does not include an Arduino board. An original Arduino board or a Chinese equivalent can be purchased separately. Code B0116 Available Regular price €56.20 -€17.39 Price €38.80
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €6.49
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.79
MQ-4 Gas Methane Sensor Module for Arduino MQ-4 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-4 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:200ppm- 10000ppm CH4, natural gas- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0028 Available Price €2.95
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €3.29
MG-5 Gas Methane Sensor Module for Arduino MG-5 Gas Methane Sensor Module for Arduino features: - Main chip: MQ-5 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm - 10000ppm LPG, LNG, natural gas, propane,- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0029 Available Price €2.53
Kit compatible Makey Makey The Makey Makey clone board - economic and compatible - is small and has a USB port to connect it to a computer and alligator clips to connect other objects. Just plug, clip and play, no programming skills or cumbersome software installation required. With a set-up in seconds, your child can get inventing, whether at home or in the classroom. Code B0129 Available Regular price €23.95 -€1.49 Price €22.46
Arduino Engineering Kit REV2 The Arduino Engineering Kit Rev 2 is a versatile and practical learning tool. By creating fun, real-world projects, you can understand basic engineering and mechatronics concepts and learn to program in MATLAB and Simulink. The versatility of the elements gives you the opportunity to adapt the content and create your own curriculum based on it. The kit includes online courseware, step-by-step instructions, lessons and exercises. It works best when studying in small groups. Code AKX022 Available Regular price €289.95 -€15.00 Price €274.95
MyoWare Muscle Sensor Development Kit - OBSOLETE This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together. Code SP074
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 Available Price €4.29
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
Kit de Pro Mini Atmega328 5V 16M + Adaptador USB-UART CP2102 para Arduino Set of Pro Mini Atmega328 5V 16M + USB-UART Adapter CP2102 for Arduino Pro mni has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Ideal for connecting TTL RS232 devices to your PC through the USB port. Code B0018 Available Price €12.65
Relay Module 1 Channel 5V 10A 1 Channel 5V Relay Module. This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). Relay Module 1 Channel 5V 10A features: - Channel: 1 - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - LED indicator - Dimensions: 30x 54mm Code RL005 Available Price €1.29
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
Relay Module DC 5V 10A 2 Channel Low/High Trigger Relay Module DC 5V 10A 2 Channel Low/High Trigger features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- It has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL002 Available Price €3.15
Water Level Sensor Module One Mega Pic Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm Code S0023 Available Price €1.39
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €7.49
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €7.49
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44
Qwiic cable kit The SparkFun Qwiic Cable Kit includes 10 cables of different lengths and styles that will connect your Qwiic boards to each other, to a development platform or to a breadboard. Each Qwiic cable is colour coded red, black, blue and yellow with 1mm JST termination. Code SP098 Available Price €11.95
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
Gravity: Huskylens - An easy-to-use AI camera | vision sensor Huskylens is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0305) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF013 Available Price €71.49
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
SparkFun DataLogger IoT - 9DoF SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project. Code SP099 Last items in stock Price €94.90
Lilypad Battery Support Button Cell 3V CR2032 Lilypad Battery Support Button Cell 3V CR2032 features: - Battery holder for your Lilypad projects - For 20mm diameter battery type CR2032 - ON / OFF control - Connection points: 4 Code M0072 Available Regular price €3.99 -€1.00 Price €2.99
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.89
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Buzzer 5V Active Buzzer 4 to 7V DC Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects. Buzzer 5V Active Buzzer 4 to 7V DC features: - Input voltage: 4V to 7V - Diameter: 12mm - Height: 9.5mm - Spacing Pins: 7.6mm - Maximum Current: Code M0007 Available Price €0.45
MQ-8 Hydrogen Gas Sensor Module MQ-8 Hydrogen Gas Sensor Module features:- Main chip: MQ-8 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 100ppm- 10000ppm hydrogen H2- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0032 Available Price €2.95