W5100 Mini Network Module Ethernet Shield Arduino compatible W5100 Mini Network Module Ethernet Shield Arduino features: - Shield Ethernet for Arduino and compatible boards based on the Wiznet W5100 chip - Provides a simple mode to connect your module to the local network and the internet - Compatible with the official Arduino Ethernet library - With this shield you can build a web server - It can be used as a server or as a client - Controller: Wiznet W5100 - Supports TCP and UDP protocols - Supports up to 4 simultaneous connections - Compatible with all versions of Arduino: UNO, mega 1280/2560 - Dimensions: 50 x 25x 25mm Code W0074 ✗ Out-of-Stock Price €9.01
Resistor 2,2K Ohm 5% 0,25W 1/4W Resistor 2,2K Ohm 5% 0,25W 1/4W features:-2.2K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0015 Available Price €0.07
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.31 -€0.39 Price €1.92
ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 55x 35x 16 mm Code W0002 Available Price €7.43
Resistor 2K Ohm 5% 0,25W 1/4W Resistors 2K Ohm 5% 0,25W 1/4W features:-2 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0014 Available Price €0.07
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.40
10x Tactile Tact Push Button Switch 6x6x8mm 10x Tactile Tact Push Button Switch 6x6x8mm features:- Tactile Push Tact Switch mini electronic Arduino pushbutton- Measures: 6x6x8mm- Quantity: 10 units Code K0076 Available Price €0.12
Digital Thermometer with External Temperature Probe - Immerse the probe in the fish tank to measure the water temperature Digital Thermometer with External Temperature Probe features: - Cable length: 1m- LCD screen- Temperature range: -50 C ~ + 70C- Powered by 2 batteries x LR44 / AG13 button (included)- Cable length: approx.100cm- External Dimensions: 48 x 28.5 x 15.2 mm- Dimension LCD screen: 35 x 16 mm- Color: Black- Used to measure the temperature in: the rooms, the aquarium, terrarium in the heating system, in the car, fridge, freezer Code S0039 Available Price €2.31
Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 50.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0091 Available Price €0.40
DS18B20 Submersible Probe Sensor Temperature Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.DS18B20 Submersible Probe Sensor Temperature features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Red Vcc - Yellow digital output- Inocidable steel- Cable length: 1m Code S0019 ✗ Out-of-Stock Price €1.98
Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 1.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0088 Available Price €0.40
Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 5.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0089 Available Price €0.40
Tuya Smart - ZigBee 3.0 temperature and humidity sensor ZigBee temperature and humidity sensor provides accurate temperature and humidity measurements and stores this data in memory for one year. Broken down into days with hours, months and a year. Code WT004 Available Regular price €12.31 -€3.00 Price €9.31
Dallas Temperature Sensor Module DS18B20 The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features: - Operating voltage: 3 - 5.5 VDC - Measurement operating temperature: -55 ° C - 125 ° C - Output current: 5 μA - Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C - Storage temperature: -55 ° C - + 125 ° C - 100% new and high quality - Module DS18B20 temperature measurement sensor - The DS18B20 sensor has a pull-up resistor - Power indicator LED on the module Code S0124 Available Price €1.61
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €6.57
Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 10.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0090 Available Price €0.40
Temperature Sensor Module MLX90614ESF-BAA GY-906 The GY-906 BAA is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, within 3 cm the precision is higher, approximately 0.5 degrees Code S0145 Available Price €8.22
DS18B20 Digital Temperature Sensor Probe 10m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 10m. DS18B20 Digital Temperature Sensor Probe 10m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 10m Code S0127 Available Price €12.39
Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 50.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0091 Available Price €0.40
DS18B20 Submersible Probe Sensor Temperature Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.DS18B20 Submersible Probe Sensor Temperature features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Red Vcc - Yellow digital output- Inocidable steel- Cable length: 1m Code S0019 ✗ Out-of-Stock Price €1.98
Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 1.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0088 Available Price €0.40
Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 5.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0089 Available Price €0.40
Tuya Smart - ZigBee 3.0 temperature and humidity sensor ZigBee temperature and humidity sensor provides accurate temperature and humidity measurements and stores this data in memory for one year. Broken down into days with hours, months and a year. Code WT004 Available Regular price €12.31 -€3.00 Price €9.31
Dallas Temperature Sensor Module DS18B20 The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features: - Operating voltage: 3 - 5.5 VDC - Measurement operating temperature: -55 ° C - 125 ° C - Output current: 5 μA - Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C - Storage temperature: -55 ° C - + 125 ° C - 100% new and high quality - Module DS18B20 temperature measurement sensor - The DS18B20 sensor has a pull-up resistor - Power indicator LED on the module Code S0124 Available Price €1.61
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €6.57
Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 10.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0090 Available Price €0.40
Temperature Sensor Module MLX90614ESF-BAA GY-906 The GY-906 BAA is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, within 3 cm the precision is higher, approximately 0.5 degrees Code S0145 Available Price €8.22
DS18B20 Digital Temperature Sensor Probe 10m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 10m. DS18B20 Digital Temperature Sensor Probe 10m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 10m Code S0127 Available Price €12.39