Buzzer 5V Active Buzzer 4 to 7V DC

This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, from the TTL 8 Channel High Trip 5V 10A Relay Module features:
- Channels: 8 (independent protected with Optocouplers)
- Supply Voltage Vcc: 5Vdc
- Output Current: 10A
- High trip min 3.3V input IN1. ..IN8
- Relay activation current: 5 ~ 10mA
- Isolation: Yes
- Indicator LED: For each channel
- Dimensions: 55x 139mm
- Weight: 120g
COM GND jumper input: connects GND optocouplers and GND of the circuit

5 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)

SIM808 GPRS GSM GPS Bluetooth SIM Quadband features:
- SIM card SIM808 GPRS GSM GPS Bluetooth SIM
- Supply voltage range: 3.4-4.4V
- Four bands GSM 850/900/1800 / 1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- According to GSM phase 2/2 +
- Class 4 (2 W at 850/900 MHz)
- Class 1 (1W at 1800 / 1900MHz)
- Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com)
- Operating temperature: -40 to + 85 ° C
- PCB dimension: 38x38mm
- GPS sensitivity
- Tracking: -165dBm Cold start Sensitivity
- Cold start: -147dBm
- Time to first solution
- Cold start: 30 s
- Start to warm up: 28s
- Already hot: 1s - Accuracy

Relay SRD-05 DC-2P 5V 10A SPDT features:
- Supply voltage: 5V
- Output Current: 10A
- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica

This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project.

The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll.

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB

This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.
Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features:
- Interfaces:
       - 5V micro USB supply
       - USB audio
       - U disk
       - LED
       - TF card
       - IR remote
       - AD key interface to connect external circuits
       - Bluetooth decoder
       - 3.5mm stereo output
       - Left and right 3W channels handling speaker
       - 2 3W amplifiers
- Supply voltage: 3.7-5VDC
- Signal / noise ratio (SNR): 90 dB

The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.
Several of these individual sessions can be chained together to form a screen or an addressable string.
Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:
- Use the WS2812S chip
- RGB color lights
- Each LED can be controlled individually
- You only need one control line and two power cables
- Arduino libraries and routines available
- Density of the PCB: 0.8 mm
- Size: 20x3 mm

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode: