Weather sensors

Barometric Pressure, Temperature and Altitude Sensor BMP180 features:
- Module based on the atmospheric pressure sensor BMP180
- Supply voltage: 1.8 - 3.6 V
- Energy consumption: 0.5uA
- I2C interface
- Measuring range: 300 - 1100hPa
- Dimensions: 10 x 13 mm
- Includes soldering pins

This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.
The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.
Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features:
- Interfaces:
       -I2C (up to 3.4 MHz)
       -SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
       - Temperature: -40ºC to + 85ºC
0-100%
       - Pressure: 300-1100 hPa
- Resolution of the measures:
       - Temperature: 0.01ºC

This module includes the component BME280 that is translated into a digital signal.
The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.
Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features:
- Interfaces:
- I2C (up to 3.4 MHz)
- SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
- Temperature: -40ºC to + 85ºC
- Humidity: 0-100%
- Pressure: 300-1100 hPa
- Resolution of the measures:
- Temperature: 0.01ºC
- Humidity: 0.008%
- Pressure: 0. 18Pa
- Accuracy of the measures:
- Temperature: +/>

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board.

The BME280 is an environmental sensor (SEN0236) integrating a temperature sensor, a humidity sensor and a barometer. Powered from 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: 300 hPa to 1100 hPa.

The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors.

The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery.

The SparkFun Weather Meter Kit is a set of basic mechanical and electronic components to build a weather station. With the SparkFun Arduino IoT Weather Station kit in sight, you can create your own weather station. The kit allows monitoring via the Arduino Cloud, an IoT platform.