Arduino Modules

W5100 Mini Network Module Ethernet Shield Arduino features:
- Shield Ethernet for Arduino and compatible boards based on the Wiznet W5100 chip
- Provides a simple mode to connect your module to the local network and the internet
- Compatible with the official Arduino Ethernet library
- With this shield you can build a web server
- It can be used as a server or as a client - Controller: Wiznet W5100
- Supports TCP and UDP protocols
- Supports up to 4 simultaneous connections
- Compatible with all versions of Arduino: UNO, mega 1280/2560
- Dimensions: 50 x 25x 25mm

Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features:

Specifications of the emitter module: - Power supply: 3V ~ 12V
- Working intensity: max = 40mA (at 12V), min = 9mA (at 3V)
- AM ASK / OOK modulation
- SAW filter
- Working frequency: 315MHz-433.92MHz
- Transmission power: 25mW (315MHz at 12V)
- Range: 20 to 200 meters (different voltages can give different results)
- Transfer speed: 4 kB / S
- Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V
- Work intensity: 5.5mA (at 5.0VDC)
- Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

 Master Slave Bluetooth Modul for Arduino iOS Android. The HM10 supports Bluetooth 4.0 (low energy) and therefore has a relatively low power consumption.

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

RTC DS3231 clock module with EEPROM 32k.
High precision RTC module.
Can be used in projects of Arduino, PIC, AVR, STM32 and other.
DSC321 AT24C32 with Real Time Clock RTC Battery features:
- Based on DS3231
- EEPROM AT24C32 (32K)
- I2C interface
- LED work indicator
- Includes CR2032 3V battery

The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks.

NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features:
- The NRF24L01 + module is powered with 3.3V
- This adapter module includes a 3.3V voltage regulator
- You can connect the NRF24L01 module on it at 5V voltage
- Dimensions of PCB: 25x 18mm
- Quantity: Adapter 1 unit

Mini Submersible Water Pump DC 5.5-12V 200L / H 3W
Mini Submersible Water Pump DC 12V 200L/h 3W ARDUINO features:

* Operating voltage: 5.5-12V * Max flow: max. 200 l / h * Maximum pumping height: 40cm- max. 150cm * Cable length: 140cm * Jack DC 5.5x2.1mm connector (ext / int) * Outlet diameter: 8 mm * Dimensions: 36mm x 25mm

8x8 LED Matrix Kit MAX7219 Arduino PIC Dot Matrix Display Cascade DIY features:
- 8X8 LED matrix controlled by MAX7219 chip
- 3mm red LED
- SPI communication
- Voltage: 4.7 - 5.3V DC
- Interfaces to manage multiple modules in cascade
- Matrix dimensions: 32mm x 32mm x 8mm
- PCB dimensions: 32mm x 50mm

NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features:
- Standard: NFC Forum Type2 Tag Ntag215
- Protocol: ISO14443A
- Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ
- Reading distance: 0-10CM
- Communication speed: 106Kboud
- Working temperature: -20ºC to 70ºC
- Number of uses 100,000 times
- Data retention: 10 years
- Material: PVC
- Dimensions 86 x 54 x 0.84 mm

The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features:
- Chip ENC28J60 Microchip
- Module: 10Base-T
- 3.3V power
- SPI interface
- 25Mhz speed
- LED status LED
- Hanrun network transformer
- Network Interface board HR911105A
- Operating temperature: -40ºC to + 85ºC
- Dimensions: 51 x 19 x 16 mm

2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 12V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, from the TTL 8 Channel High Trip 5V 10A Relay Module features:
- Channels: 8 (independent protected with Optocouplers)
- Supply Voltage Vcc: 5Vdc
- Output Current: 10A
- High trip min 3.3V input IN1. ..IN8
- Relay activation current: 5 ~ 10mA
- Isolation: Yes
- Indicator LED: For each channel
- Dimensions: 55x 139mm
- Weight: 120g
COM GND jumper input: connects GND optocouplers and GND of the circuit

It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features:
- Based on chip NRF24L01 + Ultra Low Power
- Free band: 2.4GHz ISM
- Speed: 250kbps, 1Mbps, 2Mbps
- Working current - reception: 13 mA
- Transmission: 11 mA (900nA -deep sleep mode)
- Receiving sensitivity: -94dB 250kbps
- Coverage in closed spaces: 15m / 30m
- SPI interface
- Input voltage: 1.9V- 3.6V
- Input / output port voltage: 0V-3.3V / 5V
- Coverage in open areas: 100m approx.
- Clock frequency: 16MHz

WS2812 RGB 5050 Smart Addressable 5V Arduino LED WS2811 features:
- WS2812 are LEDs that have built-in logic, making it possible to vary the color of each LED individually
- WS2812 includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are individually indexable.
- They are based on the 5050 LED
- 24-bit color control (8-bit PWM per channel)
- 16.8 millions of colors per LED
- One-wire communication
- Power: max. 5 Vdc
- Current: 18.5mA
- Input and output terminals (data and power)

NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features:
- Operating voltage: 5V
- Wait time of the module receives the data: more than 2S
- The waiting time of the module sends data: more than 300
- Transfer speed: 50 Byte / S (theoretical value)
- I2C / TWI address: 0 x 47 (decimal 35)
- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)
- Size: 44 x 23 mm

Relay SRD-05 DC-2P 5V 10A SPDT features:
- Supply voltage: 5V
- Output Current: 10A
- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica

High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side.
Ideal for your Arduino projects, but can also be used with other microcontrollers.
Matrix Membrane Keyboard 4x4 Modulo features:

- Rating circuit, Max: DC 35V 100 mA
- Cable length: 85 mm
- Dupont 8 pin connector
- Specific insulation: 100 M Ohm, 100V
- Useful life: + 1 million uses
- Contact parting:

Characteristic:
- Channels: 4 (independent protected by Optocouplers)
- Supply Voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Isolation: Yes
- Indicator LED: For each channel
- Dimensions: 54x 72mm
- 5V Optocoupled 4-Channel Relay Module
- This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
User manual for the remote control + 4-channel 315 MHz IC2262 receiver:
- Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver

NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features:
- The NRF24L01 + module is powered with 3.3V
- This adapter module includes a 3.3V voltage regulator
- You can connect the NRF24L01 module on it at 5V voltage
- Dimensions of PCB: 25x 18mm
- Quantity: Adapter 1 unit

Relay Module DC 12V 10A 1 Channel Low/High Trigger features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 12V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)

W1209 12V DC Thermostat Digital Temperature Controller Switch features:
- Model: W1209
- Supply voltage: DC 12V
- Temperature control mode: ON / OFF
- Temperature range: -50 -110 ° C
- Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C
- Measurement accuracy: 0.1 ° C
- Refresh rate: 0.5 s
- Temperature protection 0-110 ° C
- Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA
- Power of output: 10A relay
- Sensor probe: NTC waterproof sensor (10K 0.5%)
- Environmental requirements: -10 ~ 60 ° C Humidity 20% -85%
- Dimensions: 48 x 40 mm

1 Channel 5V Relay Module.
This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL).
Relay Module 1 Channel 5V 10A features:

- Channel: 1
- Supply Voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- LED indicator
- Dimensions: 30x 54mm

Relay Module DC 5V 10A 2 Channel Low/High Trigger features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- It has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features:
* Power 3.0V -6V
* 3.3V / 5V logic levels
* Bluetooth version V2.1 + EDR
* Frequency: 2.4GHz ISM band
* Reach approx. 30m
* Security: Authentication and encryption
* Supports AT commands for configuration through a serial port
* Working temperature: -20 ºC to +75 ºC
* Working current - 50 mA
* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification
-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)
- Built-in hardware protector, never hangs

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

Lilypad Battery Support Button Cell 3V CR2032 features:
- Battery holder for your Lilypad projects
- For 20mm diameter battery type CR2032
- ON / OFF control
- Connection points: 4

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

W1209 DC 12V Thermostat + Transparent Box Temperature Controller features:
- Model: W1209
- Supply voltage: DC 12V
- Temperature control mode: ON / OFF
- Temperature range: -50-110 ° C
- Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C
- Measure accuracy: 0.1 ° C
- Refresh rate: 0.5s
- Temperature protection 0-110 ° C
- Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA
- Output power: 10A relay
- Probe sensor: NTC (10K 0.5%) Waterproof Sensor
- Environmental requirements: -10 ~ 60 ° c Humidity 20% -85%
- Dimensions: 48 x 40mm

Ideal for your arduino projects, but can also be used with other microcontrollers. Double Joystick Module 2 Axis XY PS2 features:
- Two axes (XY)
- Return to the center
- Central push button
- Connections: + 5Vcc / GND / VRx / VRy / SW
- Dimensions: 4 x 2.6 x 3.2cm

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

NodeMcu module based on ESP8266 controller and programming in Lua language.
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12.
It works as a standard WiFi 802.11 b / g / n 2.4 GHz.
USB communication - the CH340 chip. Characteristics of ESP 12E:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- TCP Stack / Integrated IP
- PLLs, Regulators and Integrated Power Management Units
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode

DS3231 Precision RTC Real Time Clock Module AVR ARM features:
- Can be used in projects of Arduino, Raspberry Pi, PIC, AVR
- Function compatible with the DS 3231
- Power supply voltage: +2.3 V to +5.5 V
- Temperature range: -40 ° C to + 85 ° C
- Low energy consumption
- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation
- Two alarm calendar
- Interface: I2C

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

- This module includes PA preamplifier and LNA (Low-noise amplifier)
- Comes with the SMA antenna for 2.4GHz (2dB)
- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer
- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features:
* Based on chip NRF24L01 +
* Free band: 2.4GHz ISM
* Speed: 250kbps, 1Mbps, 2Mbps
* Work current
- Reception: 45 mA
- Transmission: 115 mA (4.2uA -sleep mode)
* Receiving sensitivity:
-104dB 250kbps
- 95dB 1Mbps
- 92dB 2Mbps
* SPI interface

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0.

The bluetooth HC-05 module is one of the best options for projects where you need wireless communications.
The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features:
- CSR BC417 Chipset
- Power: 3.3.
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Approximate range: 10m
- Security: Authentication and encryption
- Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
temperature: -20 ºC to +75 ºC

Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
The display module 4-digit LED with TM1637.
The unit can be controlled with just two DIO and CLK control lines.
TM1637 4-Digit Digital Display Module features:

- 3V-5V supply voltage
- Current consumption 250 mA
- 7-segment display 4 digits common anode
- Digit size: 0.36 inches
- Dimensions: 42x24x11mm

Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.
Provides seconds, minutes, time and date, calendar up to the year 2100.
DS1302 Real Time Clock RTC Module AVR ARM PIC features:
- Chip: DS1302
- Power supply: 2V-5V
- Operating current: <2mA
- Dimensions: 44 x23 x 8mm
- Battery not included in this sale
- Connect the RTC to your Arduino
VCC -> Arduino + 3.3V
GND -> Arduino Gnd
CLK -> (SCLK_PIN)
DAT -> (IO_PIN)
RST -> (CE_PIN)

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
AL422B Video buffer consists of 3M-bits of DRAM, and it is configured as 393.216 x 8 bit FIFO (First In First Out). The interface is very easy to use because all operations are controlled by the internal DRAM memory controller. VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps features:
- Input voltage: 2.5V-3V
- Controller: AL422B FIFO buffer
- Operating power: 60mW / 15fps VGA YUV
- VGA resolution: 640x480 pixels (30fps),
- Maximum frame rate: 30fps VGA
- Flicker: 50Hz / 60Hz auto detection
- Lens size: 1/6 "
- Angle of view: 25 ° - Sensitivity: 1.3V / (lux- sec)
- SCCB (Serial Camera Control Bus) interface
- Output format: 8 Bits
- YUV />

Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features:
- Transceiver based on the SI4432 Silicon Labs chip
- Ultrathin ultra small (16.5 × 17 mm)
- Good harmonics: easy for FCC / CE certification
- Penetration capacity (measured through 8 floors)
- Frequency range: 433.92MHz
- Sensitivity down to -121 dBm
- Maximum output power: 20dBm
- Data transfer rate: 0.123-256 kbps
- FSK, GFSK and OOK modulation
- Power supply: 1.8-3.6 V
- Ultra low power shutdown mode
- Digital indication of received signal strength (RSSI)
- Time to wake up
- Bidirectional antenna switch control and automatic adjustment
- Configurable packet structure
- Preamble detection

Transceiver based on the SI4432 Silicon Labs chip
Industry standard model
Capacitive components manufactured by Murata with 10ppm high precision glass
Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:
- Supply voltage: 1.8 ~ 3.6VDC
(Note: a voltage higher than 3.6 V will cause permanent damage to the module)
- Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage)
- Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass)
- Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k)
- Transmission power: up to 20dBm (about 100mW)
- Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended)

Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip.
Provides an easy way to connect your module to the local network now internet.
Compatible with the official Arduino Ethernet library.
With this shield you can build a web server.
It can be used as a server or as a client.
It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features:
- Controller: Wiznet W5100
- Supports protocols TCP and UDP
- Supports up to 4 simultaneous connections
- Compatible with all Arduino versions: UNO, mega 1280/2560
- Dimensions: 74 x 54 x 25mm

A compact, low-power Bottom Effect System Transceiver.
Transceiver based on the SI4463 Silicon Labs chip.
Industry standard model.
In full power operating conditions, open the communication distance up to 2000 km.
Much more than the SI4432.
Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver.
Higher sensitivity -126dBm.
The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation.
The data rate in the range of 100bps ~ 1Mbps.
Operating voltage of 1.8V ~ 3.6V.
FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features:
- Supply voltage: 1.8 ~ 3.6VDC

Characteristic: - Operating voltage: 3-6V
- Max flow: 80-120 l / h
- Maximum pumping height: 40-110cm
- Continuous working time of 500 hours
- Cable length: 20cm
- Inside outlet diameter: 5 mm
- Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm

SIM808 GPRS GSM GPS Bluetooth SIM Quadband features:
- SIM card SIM808 GPRS GSM GPS Bluetooth SIM
- Supply voltage range: 3.4-4.4V
- Four bands GSM 850/900/1800 / 1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- According to GSM phase 2/2 +
- Class 4 (2 W at 850/900 MHz)
- Class 1 (1W at 1800 / 1900MHz)
- Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com)
- Operating temperature: -40 to + 85 ° C
- PCB dimension: 38x38mm
- GPS sensitivity
- Tracking: -165dBm Cold start Sensitivity
- Cold start: -147dBm
- Time to first solution
- Cold start: 30 s
- Start to warm up: 28s
- Already hot: 1s - Accuracy

TPA3118 1X60W PBTL Channel Only Amplifier features:
- Chip: TPA3118
- Power supply: DC 8V ~ 24V
- Channel type: Single channel
- Output power: 1 x 60 W.
- Matching output: 4 ~ 8 Ohm
- Mono PBTL mode
- Size (LxWxH): 46 x 35 x 13 mm

Shield Li-Po Battery for WeMos D1 Mini ESP826 features:
Connect the lithium battery to this shield to supply power for the entire D1 mini system.
When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V
- Charging current: max: 1A
- Voltage lithium battery: 3.3-4.2V
- Boost power supply: 5V (max: 1 A)
- LED color: red for charging, green for fully charged
- Ports:
* Micro USB - Charging port (normal 5V)
* Connect to the lithium battery (normal 3.3-4.2V)
* J1 - setting the maximum charging current, 0.5 A or 1A