DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
120x Female-Male Cables Female-Female Male-Male Dupont Jumpers 2.54 for Arduino 120x Female-Male Cables Female-Female Male-Male 2.54 Jumpers Dupont Arduino features:- Length: 20cm- Quantity: 120 cables- Female-Female 40 units- Male-Male 40 units- Female-Male 40 units Code K0103 Available Regular price €7.47 -€1.48 Price €5.99
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.95
Mini Submersible Water Pump DC 12V 200L/h 3W for ARDUINO Mini Submersible Water Pump DC 5.5-12V 200L / H 3W Mini Submersible Water Pump DC 12V 200L/h 3W ARDUINO features: * Operating voltage: 5.5-12V * Max flow: max. 200 l / h * Maximum pumping height: 40cm- max. 150cm * Cable length: 140cm * Jack DC 5.5x2.1mm connector (ext / int) * Outlet diameter: 8 mm * Dimensions: 36mm x 25mm Code M0111 Available Price €9.95
Acrylic Box for Arduino Mega2560 Protection box for Arduino Mega2560 made with high quality acrylic material. Arduino Mega2560 Acrylic Box features: - Compatible with Arduino Mega2560 - Material: transparent acrylic - External dimensions: 112x 65x 18mm Code B0007 Available Price €1.95
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €9.90
W5500 Ethernet Network Modules SPI 8 sockets The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this module. It can be used as a server or as a client. Code W0105 Available Price €9.99
W5500 Lite - Ethernet Network Modules SPI The WIZ850io is a compact sized network module (Ethernet module) for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the WIZNET Ethernet-based local network and internet with a TCP/IP interface. Compatible with libraries with the same Ethernet API. With this module with RJ-45 port you can build a web server. It can be used as a server or as a client. Code W0107 Available Price €9.99
W5500 Ethernet Arduino Shield UNO Web Server Expansion Module The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this UNO board shield. It can be used as a server or as a client. Code W0106 Available Price €19.50
ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 55x 35x 16 mm Code W0002 Available Price €8.99
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €9.90
W5500 Ethernet Network Modules SPI 8 sockets The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this module. It can be used as a server or as a client. Code W0105 Available Price €9.99
W5500 Lite - Ethernet Network Modules SPI The WIZ850io is a compact sized network module (Ethernet module) for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the WIZNET Ethernet-based local network and internet with a TCP/IP interface. Compatible with libraries with the same Ethernet API. With this module with RJ-45 port you can build a web server. It can be used as a server or as a client. Code W0107 Available Price €9.99
W5500 Ethernet Arduino Shield UNO Web Server Expansion Module The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this UNO board shield. It can be used as a server or as a client. Code W0106 Available Price €19.50
ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 55x 35x 16 mm Code W0002 Available Price €8.99
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95