A3967 DC Motor PAP Driver Stepper - Easy driver

Driver capable of handling up to two high consumption motors.
We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables.

Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features:

It allows controlling many different types of engines: - Up to 4 bidirectional current motors
- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos.                   L293D Motor Drive Shield Expansion Board features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A (650mA)
- Logic voltage: 5V
- Controller L293D
- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.
Pull-down resistors keep the motors off during startup.

This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos.
It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity.
PCA9685 digital servo motor controller 16 channel PWM features:

- Supply voltage: 3-5 VDC,
- Maximum motor voltage: 6 VDC,
- Number of channels: 16,
- Resolution per channel: 12 bits,
- Interface: I2C,
- Working frequencies: 40-1000 Hz,
- PCB size: 62.3x25.3mm .

The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased.

Mosfet 24V 5A IRF520 PWM controller features:
- The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater.
- The built-in IRF520 N-MOSFET transistor
- Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI)
- Charging voltage: 0-24V
- Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point)
- 60W max power (more than 10W must be equipped with a heat sink)
- Terminalblock connectors
- LED indicating the presence of power
- Dimensions: 33x24mm

Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor.

The module for DIY Arduino hobby
Motor driver L9110 for Arduino, Smart Car, Robotics
Small magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features:
- Operating voltage: 5V
- PCB dimension: 3.5 x 2.6cm
- Double red propeller
- Blade length 75mm
- Weight: 6 g
- Quantity:
  1x DC motor
  1x double helix

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:
- Stepper motor 28BYJ-48 + ULN2003 controller
- The 28BYJ-48 has everything you need to start using motors step by step in your project
- A stepper motor converts digital impulses into small steps of movement in one direction
- The motor also comes with a ULN2003 motor controller card
- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA
- Equipped with state indicator LEDs A, B, C, D
- Engine model: 28BYJ-48
- Phasing Engine: 4
- Operating voltage: 12V DC
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 Ohm
- Angle per step: 5,625º
- Steps per round: 64

LSC-16 Digital Servo Motor Controller 16 channels features:
- With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU.
- CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed.
- 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions!
- Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically).
- 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor.