Third hand support for cable soldering Third hand stand for easy soldering of wires with a diameter from 1 to 5mm. Number of holes 5. Code MX0001 ✗ Out-of-Stock Regular price €3.13 -€0.90 Price €2.23
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €2.60 -€0.50 Price €2.10
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €2.88
Sensor SCT-013-030, Non-Invasive 30A AC Current Meter The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-030, Non-Invasive 30A AC Current Meter features: Input current: 0 to 30A AC Output voltage: 0 to 1 V AC Built-in load resistance: 62 Ω Winding ratio: 1800: 1 Operating temperature range: -25 ° C to 70 ° C Cable length: 1 m Sensor weight: approximately 45 g Sensor SCT013-030 datasheet Code M0203 Available Price €5.36
DC Gear Motor and Tire Wheel for Smart Car Robot DC Gear Motor and Tire Wheel for Smart Car Robot features:- Voltage: 3 to 6 Vdc- Reduction: 1:48- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0011 Available Price €3.21
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.44
USB Cable for Arduino Type A-B USB Cable for Arduino Type A-B features: - Length: 50cm- Color: Blue Code K0158 Backorder Price €1.23
5x Push Switch Button B3F Omron Red Key 12mm 5x Push Switch Button B3F Omron Red Key 12mm features:- 5x Push Buttons B3F Omron Key- Maximum current: 50 mA- Tension DC: 24V- Operating force: 1.27N- Switch terminals: weldable- Contact: SPST-NO- Contact resistance: 100M Ohm- Type of action: Superficial- Measures: 12x12x7.3mm Code K0073 Available Price €0.16
Servo Motor Type S3003 Aeromodelling Servo Motor Type S3003 Aeromodelling features: - Operating voltage: 4.8 V to 6 V - Max torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degree (4.8V), 0.19sec / 60 degree (6V) - Max radius: 180 ° (90º in each direction) - Temperature range: - 20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese Manufacture Code R0017 Available Price €5.20
Micro Motor 3V 5V 6V DC with cable conector male For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features: - Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0080 Available Regular price €1.61 -€0.26 Price €1.35
Heat Sink Aluminium Nema 17 Heat Sink Aluminium Nema 17 features: - MK8 Extruder Radiator Heatsink Printer - Ideal for NEMA17 motors and MK7 and MK8 extruders - Dimensions 40 x 40x 11mm Code I0038 Available Price €1.48
Geared Motor with Encoder 6V 1:120 for Arduino Smart Car Robot Geared Motor with Encoder 6V 1120 Arduino Smart Car Robot features:- Voltage: 3 to 6Vdc- Speed without load: 200 RPM to 6Vdc- No-load current: 110mA at 3Vdc - 250mA at 6Vdc- Reductive: 1: 120 Code R0043 Available Price €2.85
Car Robot Tire Wheel Smart Car Car Robot Tire Wheel Smart Car features:- Dimensions of the wheel: - Diameter: 65mm - Width: 26 mm- Quantity: 1 unit Code R0009 Available Regular price €1.57 -€0.41 Price €1.16
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.40
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
Green Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0032 Available Price €1.46
DC Gear Motor N20 200 RPM 12V DIY Robot DC Gear Motor N20 200 RPM 12V DIY Robot features: - Voltage: 12V- Speed of rotation: 200RPM- Motor dimensions:* Diameter 12 mm* Height 24 mm- For Arduino, Smart Car, Robotics, Fans, Appliances Code R0035 Available Regular price €4.88 -€1.00 Price €3.88
Continous Rotation 360 Degree Servo S3003 Continous Rotation 360 Degree Servo S3003 features: - Operating voltage: 4.8 V to 6 V- Torque max.: 4.1kg / cm (6V)- Operating speed: 0.23sec / 60degree (4.8V), 0.19sec / 60degree (6V)- Radio max.: 360º- Temperature range: -20º + 60ºC degrees- Weight: 38 g- Cable length: 26cm- Dimensions: 40.5 x39x 20 mm- Servo connector: JR- Chinese manufacture Code R0019 Available Regular price €6.57 -€0.96 Price €5.61
Servo Motor Type S3003 Aeromodelling Servo Motor Type S3003 Aeromodelling features: - Operating voltage: 4.8 V to 6 V - Max torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degree (4.8V), 0.19sec / 60 degree (6V) - Max radius: 180 ° (90º in each direction) - Temperature range: - 20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese Manufacture Code R0017 Available Price €5.20
Micro Motor 3V 5V 6V DC with cable conector male For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features: - Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0080 Available Regular price €1.61 -€0.26 Price €1.35
Heat Sink Aluminium Nema 17 Heat Sink Aluminium Nema 17 features: - MK8 Extruder Radiator Heatsink Printer - Ideal for NEMA17 motors and MK7 and MK8 extruders - Dimensions 40 x 40x 11mm Code I0038 Available Price €1.48
Geared Motor with Encoder 6V 1:120 for Arduino Smart Car Robot Geared Motor with Encoder 6V 1120 Arduino Smart Car Robot features:- Voltage: 3 to 6Vdc- Speed without load: 200 RPM to 6Vdc- No-load current: 110mA at 3Vdc - 250mA at 6Vdc- Reductive: 1: 120 Code R0043 Available Price €2.85
Car Robot Tire Wheel Smart Car Car Robot Tire Wheel Smart Car features:- Dimensions of the wheel: - Diameter: 65mm - Width: 26 mm- Quantity: 1 unit Code R0009 Available Regular price €1.57 -€0.41 Price €1.16
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.40
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
Green Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0032 Available Price €1.46
DC Gear Motor N20 200 RPM 12V DIY Robot DC Gear Motor N20 200 RPM 12V DIY Robot features: - Voltage: 12V- Speed of rotation: 200RPM- Motor dimensions:* Diameter 12 mm* Height 24 mm- For Arduino, Smart Car, Robotics, Fans, Appliances Code R0035 Available Regular price €4.88 -€1.00 Price €3.88
Continous Rotation 360 Degree Servo S3003 Continous Rotation 360 Degree Servo S3003 features: - Operating voltage: 4.8 V to 6 V- Torque max.: 4.1kg / cm (6V)- Operating speed: 0.23sec / 60degree (4.8V), 0.19sec / 60degree (6V)- Radio max.: 360º- Temperature range: -20º + 60ºC degrees- Weight: 38 g- Cable length: 26cm- Dimensions: 40.5 x39x 20 mm- Servo connector: JR- Chinese manufacture Code R0019 Available Regular price €6.57 -€0.96 Price €5.61