Heat Sink Aluminium Nema 17

Nozzle Head 0.4mm 1.75 E3D 3D Printer features:
- Precision Nozzle: 0.4mm
- Material: Copper
- Size: 13mm x 6mm - Suitable for Filament: 1.75mm
- Quantity: 1 unit

10x Male-Male Cables 20cm Jumpers Dupont 2,54 features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have male header contacts at either end
-Compatible with female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 19.3 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices!

This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.
It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.
A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features:
- 2 high voltage channels and low voltage logic logic for bidirectional translation
- 2 low voltage channels High voltage high voltage logic in unidirectional conversion
- The board module is compatible, it can be inserted directly in the use test panel
- HV to 5 V power

Sensor used to measure the temperature of the hotend or hot bed of your 3D printer
Characteristic:
- NTC Thermistor 100 K 3950
- Impedance: 100 K (25º of Temperature)
- Accuracy: 1%
- Sensor Diameter: 1.8 mm
- Cable Length: 1 m
- Cable: AWM UL 3398 150 ° C 300V
- Ready to be installed and used. Fully insulated
- Designed to withstand the high temperatures of extrusion of plastics such as PLA and ABS

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C

This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,
The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.
The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.
It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features:
- Operating voltage: 3.3 - 5 V
- Input current: 50 mA
- Use a very sensitive photo resistance
- Use a LM393 wide voltage comparator, high quality output signal
- Adjustable potentiometer can regulate the brightness of detected light

It is not possible to reverse the polarity by mistake.
JST PHR-2 Connector 3 PIN Female 2mm features:
Manufacturer JST Connector series: PH Connector: plug Connector class: female Type of connector: conduit-board Raster of contactors: 2mm Number of pins: 3 Mechanical mounting: for conduit Voltage Working: 100V Working current: 2A Working temperature: -25 ... 85 ° C Connection version: contactless technical data sheet PH series