Motor Nema 17 1.22kg 17HS2408

Fan 12V 2x Cables 3D Reprap Printer features:
- For Prusa RepRap 3D Printer
- Voltage: 12V
- Consumption: 90mA - Speed: 7000rpm ± 10%
- Noise level: 25dB ± 10%
- Screw diameter: 3.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 28cm
- Dimensions: 30mm x 30mm x 10mm

4x Nozzle Head 1.75mm 3D Printer MK8 Extruder Reprap features:
- MK8 Precision Nozzle: 0.2 / 0.3 / 0.4 / 0.5mm
- Material: Copper
- Size: 13mm x 6mm
- Suitable for Filament: 1.75mm
- Quantity: 4 units

DC Gear Motor and Tire Wheel for Smart Car Robot features:
- Voltage: 3 to 6 Vdc
- Reduction: 1:48
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle.
HC-SR04 Ultrasonic Sensor Distance Measuring Module features:
- Supply voltage: 5V (4.5V- 6V)
- Consumption: 30 mA typical, (35 mA max)
- Interface: VCC , GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED indicator of measurement in progress
- Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm
- Quantity: 1 unit
Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry:
Automatic robot operation with obstacle detection />

High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side.
Ideal for your Arduino projects, but can also be used with other microcontrollers.
Matrix Membrane Keyboard 4x4 Modulo features:

- Rating circuit, Max: DC 35V 100 mA
- Cable length: 85 mm
- Dupont 8 pin connector
- Specific insulation: 100 M Ohm, 100V
- Useful life: + 1 million uses
- Contact parting:

Car Robot Tire Wheel Smart Car features:
- Dimensions of the wheel:
   - Diameter: 65mm
   - Width: 26 mm
- Quantity: 1 unit

Sensor Module ML8511 UV features:
- The module converts the photocurrent into voltage to detect UV intensity
- The analog voltage is proportional to UV light detecting
- The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use
- Power supply: 5V
- Analog output
- Captured wavelength: 280-390nm
- Ultra low power consumption
- Meteorological applications, skincare, industrial UV level measurement
- Dimensions of PCB: 30x22mm

Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C features:
- Oled 0.96 "Display of 128 * 64 pixels
- one yellow line and 3 blue lines
- Drive IC model SDD1306
- Power supply: 3V-5.5V
- View angle: 160 degrees
- SPI interface (I2C can be changed)
- Low consumption 0.08W
- Temperature usage: -20 to 70 ºC
- PCB board dimension: 32 x 32 mm
- OLED technology offers high contrast, significantly improves black on the screen and energy efficiency - very low consumption energy.
Applications: - Due to the size, quality and consumption of smart watch products, portable meters, medical devices, portable players, etc.