Digital Multimeter DT321B Voltmeter DT321B Digital Multimeter, Portable Multimeter, AC / DC Voltage Meter, Blue Backlight, Battery tester, Transistors tester, Acoustic Continuity Tester. Code H0195 Available Regular price €9.08 -€1.00 Price €8.08
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Regular price €6.19 -15% Price €5.26
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.82
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.62
USB Cable for Arduino Type A-B USB Cable for Arduino Type A-B features: - Length: 50cm- Color: Blue Code K0158 Backorder Price €1.23
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.09
Wio Terminal - ATSAMD51 - RTL8720DN WiFi Bluetooth - Seeedstudio Wio Terminal: ATSAMD51 Core development board with Realtek RTL8720DN BLE 5.0 & Wi-Fi 2.4G / 5G. Arduino and MicroPython compatible, Wio Terminal is an ATSAMD51-based microcontroller with wireless connectivity compatible with Realtek RTL8720DN. Its CPU speed runs at 120MHz (Boost up to 200MHz). The Realtek RTL8720DN chip supports Bluetooth and Wi-Fi, providing the backbone for IoT projects. The Wio terminal itself is equipped with a 2.4 ”LCD screen, integrated IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared emitter (IR 940 nm). Code SS010 Last items in stock Price €45.86
Heat Sink Aluminium Nema 17 Heat Sink Aluminium Nema 17 features: - MK8 Extruder Radiator Heatsink Printer - Ideal for NEMA17 motors and MK7 and MK8 extruders - Dimensions 40 x 40x 11mm Code I0038 Available Price €1.48
USB to A RS232 UART TTL 5V Converter + Cables Ideal for connecting TTL RS232 devices to your PC through the USB port. USB to A RS232 UART TTL 5V Converter + Cables features: - Compatible controller PL2303HX- 5 pins: 3.3v, 5.0v, TXR, RDX, GND- Heat shrinkable insulating cover- LED indicators of data transmission- 2.5A self-recovery protective fuse- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux- Weight: 40 gr. (approx.) Code C0009 Available Price €2.08
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €4.29
USB 2.0 to Parallel Adapter Cable DB25 Interface IEEE 1284 Printer A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" Code C0020 Available Price €2.47
SparkFun FTDI Basic Breakout - 5V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP023 Available Price €16.52
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.26
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €5.45
USB to RS485 USB to 485 Max485 Converter Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features: - CH340 controller- Supported OS: Win XP, Vista, Win 7.8, OS, Linux- Work with Modbus, Profibus- USB 2.0 specification with 6Mbps of maximum speed- Measures: 60x 18x 14 mm Code C0003 Available Price €2.22
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.26
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Logic Level Converter 3.3 / 5V I2C IIC 3.3V/5V I2C logic level converter module with soldering pins.Ideal to connect a device that works at 3.3V to one that works with 5V.It works with digital signals (high and low levels).Logic Level Converter 3.3 / 5V I2C IIC features:- Voltage: 3.3V/5V- Measures: 1.5x 1 cm Code C0004 Available Price €1.40
USB to A RS232 UART TTL 5V Converter + Cables Ideal for connecting TTL RS232 devices to your PC through the USB port. USB to A RS232 UART TTL 5V Converter + Cables features: - Compatible controller PL2303HX- 5 pins: 3.3v, 5.0v, TXR, RDX, GND- Heat shrinkable insulating cover- LED indicators of data transmission- 2.5A self-recovery protective fuse- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux- Weight: 40 gr. (approx.) Code C0009 Available Price €2.08
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €4.29
USB 2.0 to Parallel Adapter Cable DB25 Interface IEEE 1284 Printer A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" Code C0020 Available Price €2.47
SparkFun FTDI Basic Breakout - 5V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP023 Available Price €16.52
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.26
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €5.45
USB to RS485 USB to 485 Max485 Converter Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features: - CH340 controller- Supported OS: Win XP, Vista, Win 7.8, OS, Linux- Work with Modbus, Profibus- USB 2.0 specification with 6Mbps of maximum speed- Measures: 60x 18x 14 mm Code C0003 Available Price €2.22
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.26
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Logic Level Converter 3.3 / 5V I2C IIC 3.3V/5V I2C logic level converter module with soldering pins.Ideal to connect a device that works at 3.3V to one that works with 5V.It works with digital signals (high and low levels).Logic Level Converter 3.3 / 5V I2C IIC features:- Voltage: 3.3V/5V- Measures: 1.5x 1 cm Code C0004 Available Price €1.40