Resistor 330 Ohm 5% 0,25W 1/4W Resistor 330 Ohm 5% 0,25W 1/4W features:-330 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0009 Available Price €0.07
Dupont Connector 2.54mm Female Dupont Connector 2.54mm Female features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0110 Available Price €1.81
DS18B20 Submersible Probe Sensor Temperature Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.DS18B20 Submersible Probe Sensor Temperature features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Red Vcc - Yellow digital output- Inocidable steel- Cable length: 1m Code S0019 ✗ Out-of-Stock Price €1.98
L7812 Voltage Regulator 12V 1.5A TO-220 7812 for Arduino L7812CV L7812CV Voltage Regulator 12V 1.5A TO-220 7812 Arduino L7812CV features:-Type Output: Fixed-Voltage Output: 12V-Manufacturer: ST Microelectronics-Output current: 1.5A-Max input voltage: 35V-Input input min.: 5V-Operational temperature: 0ºC to + 125ºC-Encapsulated: TO-220-Polarity: Positive Code T0004 Available Price €0.21
LED 10-Segment Bar Graphics Display Red LED 10-Segment Bar Graphics Display Red features: - Bargraph LED display - Number of segments: 10 - Size: 5mm - Dimensions: 25x10mm - Material GaAsP / GaP - Color: red - Wavelength: 635 nm - Vf / forward /2.1 V - I fw / forward / 30 mA - Iv / Ifw = 20mA / 4 mcd - Number of terminals: 20 Code P0100 Available Regular price €0.93 -€0.14 Price €0.79
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €3.71
Rocker switch KCD4 momentary 15A 250V Double (ON)-OFF Red 4-pin The AC 250V 15A 4-pin DPST (on/off) type rocker switch. Code K0401 Available Price €1.57
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.06
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.39
Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features: - Working voltage and TTL levels: 5V- Size: 44 x 14 mm Code C0013 Available Price €1.61
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €4.29
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Adapter / Converter HDMI male - VGA female + Audio Jack cable Descripción: El adaptador de HDMI a VGA le permite conectar un monitor, proyector o LCD analógico estándar que usa un conector o cable VGA a un cuaderno, DVD, TVbox, reproductor BIU-rog, computadora, proyector. Característica: - Tipo: adaptador/convertidor AV,- Conector A: HDMI macho,- Conector B: VGA hembra,- Conexión Split / Duplicación: ninguna (1: 1),- El adaptador dispone de una entrada audio Jack hembra,- Ancho del cable del adaptador: 15cm,- Incluye un cable audio Jack macho de ambos lados,- Ancho del cable audio: 52cm,- Color: blanco. Code C0019 Available Price €6.20
TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features: - 2 high voltage channels and low voltage logic logic for bidirectional translation- 2 low voltage channels High voltage high voltage logic in unidirectional conversion- The board module is compatible, it can be inserted directly in the use test panel- HV to 5 V power Code M0154 Available Regular price €3.79 -€1.60 Price €2.19
FTDI FT232RL USB-UART Converter - Mini USB FTDI FT232RL USB-UART Converter - Mini USB features: - Serial Converter USB-TTL 3.3V - 5V - LED indicator of Tx, Rx, power. - Communication: TTL COM Virtual RS232 RX / TX Transceiver - Voltage: 3.3V or 5V - per bridge - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA. - Size: 46 x 19 mm. Step 2.54mm. - Connection: Mini USB - Driver: Windows 7 / 8/10 Linux / Mac / Android - USB TO UART solution with mini USB connector - FT232RL original on board - Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ... - 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V) - 3 LEDs: TXD LED, RXD LED, POWER LED - Functional pins Code C0014 Available Price €10.70
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.26
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.26
USB to A RS232 UART TTL 5V Converter + Cables Ideal for connecting TTL RS232 devices to your PC through the USB port. USB to A RS232 UART TTL 5V Converter + Cables features: - Compatible controller PL2303HX- 5 pins: 3.3v, 5.0v, TXR, RDX, GND- Heat shrinkable insulating cover- LED indicators of data transmission- 2.5A self-recovery protective fuse- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux- Weight: 40 gr. (approx.) Code C0009 Available Price €2.08
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.39
Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features: - Working voltage and TTL levels: 5V- Size: 44 x 14 mm Code C0013 Available Price €1.61
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €4.29
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Adapter / Converter HDMI male - VGA female + Audio Jack cable Descripción: El adaptador de HDMI a VGA le permite conectar un monitor, proyector o LCD analógico estándar que usa un conector o cable VGA a un cuaderno, DVD, TVbox, reproductor BIU-rog, computadora, proyector. Característica: - Tipo: adaptador/convertidor AV,- Conector A: HDMI macho,- Conector B: VGA hembra,- Conexión Split / Duplicación: ninguna (1: 1),- El adaptador dispone de una entrada audio Jack hembra,- Ancho del cable del adaptador: 15cm,- Incluye un cable audio Jack macho de ambos lados,- Ancho del cable audio: 52cm,- Color: blanco. Code C0019 Available Price €6.20
TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features: - 2 high voltage channels and low voltage logic logic for bidirectional translation- 2 low voltage channels High voltage high voltage logic in unidirectional conversion- The board module is compatible, it can be inserted directly in the use test panel- HV to 5 V power Code M0154 Available Regular price €3.79 -€1.60 Price €2.19
FTDI FT232RL USB-UART Converter - Mini USB FTDI FT232RL USB-UART Converter - Mini USB features: - Serial Converter USB-TTL 3.3V - 5V - LED indicator of Tx, Rx, power. - Communication: TTL COM Virtual RS232 RX / TX Transceiver - Voltage: 3.3V or 5V - per bridge - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA. - Size: 46 x 19 mm. Step 2.54mm. - Connection: Mini USB - Driver: Windows 7 / 8/10 Linux / Mac / Android - USB TO UART solution with mini USB connector - FT232RL original on board - Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ... - 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V) - 3 LEDs: TXD LED, RXD LED, POWER LED - Functional pins Code C0014 Available Price €10.70
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.26
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.26
USB to A RS232 UART TTL 5V Converter + Cables Ideal for connecting TTL RS232 devices to your PC through the USB port. USB to A RS232 UART TTL 5V Converter + Cables features: - Compatible controller PL2303HX- 5 pins: 3.3v, 5.0v, TXR, RDX, GND- Heat shrinkable insulating cover- LED indicators of data transmission- 2.5A self-recovery protective fuse- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux- Weight: 40 gr. (approx.) Code C0009 Available Price €2.08