Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development

Characteristic:
-10k OHM kΩ - linear potentiometer 10k Arduino
-Tolerance: +/- 20%
- Power: 0.125W

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

40x Male to male cables 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont male connectors on both ends
- Compatible with 2.54mm female connectors
- High quality and good working condition
- Easy to install and use

Resistor 220K Ohm 5% 0,25W 1/4W features:
-220 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Prototype Board MB-102 Protoboard 830 points Arduino features:
- 830 Connections
- Linkable with other boards
- Base with adhesive to attach it to the work surface
- Measures 165x 55x8mm

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

ESP32-S3-DevKitC-1-N8R8 general-purpose development board based on the ESP32-S3R8-WROOM-1 chip, Flash 8MB, PSRAM 8MB.

ESP32-WROOM-32E (ESP32-DEVKITC-32E) is an evaluation board with ESP32 processor, 4MB FLASH, 802.11 a/b/g/n (Wi-Fi, WiFi, WLAN) and BlueTooth® Smart Ready 4.x dual-mode. It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use.

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

ESP32-S3-DevKitC-1-N8 general-purpose development board based on the ESP32-S3-WROOM-1 chip.

The adaptor for the well-known ESP-12 and ESP-12E module

The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot.

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

Shield Li-Po Battery for WeMos D1 Mini ESP826 features:
Connect the lithium battery to this shield to supply power for the entire D1 mini system.
When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V
- Charging current: max: 1A
- Voltage lithium battery: 3.3-4.2V
- Boost power supply: 5V (max: 1 A)
- LED color: red for charging, green for fully charged
- Ports:
* Micro USB - Charging port (normal 5V)
* Connect to the lithium battery (normal 3.3-4.2V)
* J1 - setting the maximum charging current, 0.5 A or 1A

Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins.