Optical Isolated Converter FT232RL USB 2.0 to RS485

Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features:
- Working voltage and TTL levels: 5V
- Size: 44 x 14 mm

A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" 

Standard ISP download port, for on-line programming. Built-in crystal oscillator circuit (8MHz), crystal are replaceable. Has reset push button, power reset push button. 

The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden.

This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.
It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.
A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features:
- 2 high voltage channels and low voltage logic logic for bidirectional translation
- 2 low voltage channels High voltage high voltage logic in unidirectional conversion
- The board module is compatible, it can be inserted directly in the use test panel
- HV to 5 V power

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.
Your converter has four analog inputs, one analog output and one I2C serial bus interface.
It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.
The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.
It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features:
- Supply voltage (between VSS and VDD): 2.5-6VDC

A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features:
- USB-Serial TTL 3.3V -5V Converter
- LED indicator for Tx, Rx, power supply
- Communication: Transceiver RX / TX TTL COM Virtual RS232
- Voltage: 3.3V or 5V - via jumper
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA
- Size: 35 x 17 mm Pitch 2,54mm
- Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
User manual for remote control + 4-channel receiver 315 MHz IC2262
- Wire the USB />

This is a CH340G TTL UART 5V serial adapter, designed to allow adding a USB connection to your project.
In addition, this opens up the possibility of programming microcontrollers like the Arduino Pro mini.
This module allows you to connect your project, from programming small microcontrollers to a custom computer keyboard.
The module is ready for use of a UART connection.
This may require the installation of a driver; however, it is a standard driver distributed by Microsoft Windows Update, available in Linux and that can be configured in MAC OS.
Adapter module CH340G LC Technology -TTL UART 5V series features:
- Manufacturer: LC Technology,
- Communication chipset: CH340G
- Communication: UART,
- Pin connection:

Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features:
- Compatible controller PL2303HXA
- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)
- 2.5A self-recovery protective fuse
- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error.