Relay Module 1 Channel 5V 10A 1 Channel 5V Relay Module. This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). Relay Module 1 Channel 5V 10A features: - Channel: 1 - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - LED indicator - Dimensions: 30x 54mm Code RL005 Available Price €1.07
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.47
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Potentiometer B5K Linear 5K OHM kΩ Characteristic: - Tolerance: +/- 20% - Power: 0.125W Code K0066 Available Price €0.82
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €8.22
3x Heat Sink Aluminium Adhesive A4988 DRV8825 3x Heat Sink Aluminium Adhesive A4988 DRV8825 features: - Package includes: 3x Heatsink with adhesive - Ideal for DRV8825, A4988 etc - Dimensions: 9 x 9 x 5mm Code I0046 Available Price €0.29
Battery holder 2x 18650 3,7V Serial Battery holder for 18650 batteries connected in series. Code PP057 Last items in stock Regular price €1.64 -€0.30 Price €1.34
Logic Level Converter 3.3 / 5V I2C IIC 3.3V/5V I2C logic level converter module with soldering pins.Ideal to connect a device that works at 3.3V to one that works with 5V.It works with digital signals (high and low levels).Logic Level Converter 3.3 / 5V I2C IIC features:- Voltage: 3.3V/5V- Measures: 1.5x 1 cm Code C0004 Available Price €1.40
SparkFun ESP8266 Thing - Dev Board (with Headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes with headers. Code SP008 Last items in stock Price €17.88
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €18.17
Wifi module adapter ESP12 ESP12E The adaptor for the well-known ESP-12 and ESP-12E module Code W0025 Available Price €0.74
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Price €3.93
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €2.88
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 Last items in stock Price €7.81
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €3.71
TUYA IoT Interface for controlling Arduino over WiFi TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V. Code WT017 Last items in stock Price €15.62
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP039 Last items in stock Price €28.09
ESP-01 Esp-01 Esp8266 ESP01 WiFi USB Programmer Adaptor USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART). Code W0110 Available Price €2.60
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.82
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.22 -€0.20 Price €2.02
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.64
Resistor 220K Ohm 5% 0,25W 1/4W Resistor 220K Ohm 5% 0,25W 1/4W features:-220 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0027 Available Price €0.07
Prototype Board MB102 Protoboard 830 points for Arduino Prototype Board MB-102 Protoboard 830 points Arduino features: - 830 Connections - Linkable with other boards - Base with adhesive to attach it to the work surface - Measures 165x 55x8mm Code PB004 Available Regular price €2.47 -€0.50 Price €1.97
SparkFun ESP8266 Thing - Dev Board (with Headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes with headers. Code SP008 Last items in stock Price €17.88
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €18.17
Wifi module adapter ESP12 ESP12E The adaptor for the well-known ESP-12 and ESP-12E module Code W0025 Available Price €0.74
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Price €3.93
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €2.88
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 Last items in stock Price €7.81
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €3.71
TUYA IoT Interface for controlling Arduino over WiFi TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V. Code WT017 Last items in stock Price €15.62
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP039 Last items in stock Price €28.09
ESP-01 Esp-01 Esp8266 ESP01 WiFi USB Programmer Adaptor USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART). Code W0110 Available Price €2.60