Mounting Bracket for Nema Motor 23 57mm/76mm

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

40x Male to male cables 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont male connectors on both ends
- Compatible with 2.54mm female connectors
- High quality and good working condition
- Easy to install and use

One of the most popular stepper motors with 200 steps per revolution and a maximum load of 5 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices!

Mounting Bracket for Nema Engine 17 42mm features:
- Steel bracket for PAP Nema 17 3D printer motor
- Mounting bracket of 42mm L shape alloy steel for The NEMA17 3D Stepper Motor Printer
- Material: Alloy Steel - Size: 5 x 5 x 5cm
- Black Color
- Fit for 42mm Stepper Motor as NEMA17

Wide range of voltages, improved version.
Drop module.
They will use a multimeter to Check the output voltage and adjust the potentiometer.
3A DC Converter 4-53V Adjustable LM2596H Step Down Source features:

- Based on the LM2596HVS-ADJ regulator
- Rectification: Asynchronous
- Output Voltage: 3v ~ 40v DC (adjustable)
- Input Voltage: 4.5v - 53v DC
- Max Output Current: 3A (with heat sink)
- Ripple in output voltage: 30mV
- Frequency: 150KHz
- Max Conversion Efficiency: 92%
- Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5%
- Operating temperature: -40ºC to + 85ºC
- Measurements: 43x 21x 14 mm

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

Potentiometer B1K Linear features:
-1k OHM kΩ - linear potentiometer 1k Arduino
-Tolerance: +/- 20%
- Power: 0.125W