Digital Light Intensity Sensor with Photo Resistance with LM393 Controller

Descripción: Light sensor module to measure light intensity and obtain digital data from it.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features:
- Chip BH1750FVI
- Supply voltage 3V-5V
- Integrated 16bit AD converter
- Detection range: 0-65535 lx (with an accuracy of 1 lux)
- Interface: II2C
- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)
- Dimensions 18.4 x 14 mm

Sensor Module GUVA-S12SD UV features:
- The module based on the Schottky-type photodiode - applicable to the optical mode
- This is a " true "UV sensor instead of calibrated light sensor
- It has high sensitivity, high stability, good linearity
- Power supply: 2.5V - 5V
- Analog output
- Captured wavelength: 240-370nm
- Ultra low power consumption
- Meteorological applications, skin care, industrial UV level measurement
- PCB dimensions: 11x27mm

Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode.

Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA.
100% compatible UNO module.
Characteristic:
- Operating voltage: 3.3-5 VDC
- Output voltage: 0-1 VDC
- 3-pin connector:
- OUT: output signal
- VCC: Supply voltage
- GND: Ground connection - Test accuracy: ± 1UV INDEX
- Current: 0.06mA (typical), 0.1mA (maximum)
- Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds
- Operating temperature: -20ºC - + 85ºC
- Size: 19.80 x 15mm

UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light.
Ideal for Arduino projects.
Black UV sensor module UVM-30 for Arduino features:
- Operating voltage: 3-5 VDC,
- Voltage input: DC 0-1 VDC,
- 3-pin connector:
- GND (-): ground connection,
- Out: sensor output signal,
- VCC (+): sensor supply,
- Measurement accuracy: +/- 1UV index,
- Working current: 0.06mA (standard) / 0.1mA (max.),
- Response wavelength: 200-370 nm,
- Working temperature: -20ºC - + 85ºC,
- PCB size: 28x12mm.

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Sensor Module ML8511 UV features:
- The module converts the photocurrent into voltage to detect UV intensity
- The analog voltage is proportional to UV light detecting
- The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use
- Power supply: 5V
- Analog output
- Captured wavelength: 280-390nm
- Ultra low power consumption
- Meteorological applications, skincare, industrial UV level measurement
- Dimensions of PCB: 30x22mm

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

It consists of three principles of induction of primary colors, if you know the composition of all types of color values, you can know the color of the test object.
For TCS230, a color filter is chosen, only a certain primary pass is allowed, it is stopped by another color. For example, when choosing a red filter, the incident light can only be stopped in red, blue and green, so you can get the intensity of the red beam of light.
For the same reason, the choice of other filters, can obtain the intensity of blue light and green light.
Through these three values, the color of the light can be projected onto a TCS230 sensor. Color Recognition Sensor GY-31 TCS230 TCS3200 features:
- Operating voltage: 3 - 5 VDC
- Model GY-91
- Chip TCS230 TCS3200

This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases.
On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND
2- VCC
3- analog output - the voltage depending on the light
- Supply voltage: 3.3 V-5VDC
- PCB size: 19x15x8 mm