Micro Motor 3V 5V 6V DC DIY for Arduino UNO Mega Robotics

Ideal for your electronic projects, arduino, but can also be used with other microcontrollers. Breadboard Power Supply Protoboard 830/400 Points MB102 features:
- Input voltage supports up to 12V
- Selectable 3.3V or 5V
- USB input or standard DC 2.1 x5.5mm connector
- Maximum current 700mA
- It fits perfectly on the MB-102 breadboard feeding the two lateral buses
- Weight: 15 gr. (approx.) Compatible only with MB-102 type plates

Characteristic: - Lithium Battery WITHOUT Protection
- Nominal capacity: 2600mAh (discharge of 0.2C, 2.75V)
- Minimum capacity: 2550mAh (0.2C, 2.75V discharge)
- Charging voltage: 4.2 ± 0.05 V
- Nominal voltage: 3.63V
- Charging method: DC-CV (constant voltage with current limited)
- Charging current: standard charge: 1300mA, fast charge: 2600mA
- Charging time: standard charge: 3 hours, fast charge: 2.5 hours
- Max. Charging current: 2600mA (ambient temperature 25 °)
- Max. Discharge current: 5200mA (ambient temperature 25 °)
- Discharge cut-off voltage: 2.75V
- Cell weight: 47.0g maximum
- Cell dimension: Height: 65.00 mm max., Diameter: 18.40 mm max.

It consists of a 16-character, 2-row display
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32
16x2 LCD screen 1602 Blue welded pins features:

- LCD screen, 16 characters and 2 lines
- 5V power supply
- HD44780 compatible controller
- Backlit blue background, white letters
- Includes an adjustable contrast pin - It has soldered pins and is ready to connect - Dimensions (mm): 80 x 36 x 19

- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

Sensor Module FZ0888 IR Infrared Speed Meter features:
- The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position
- The module has a digital output (DO) which can be connected to your preferred microcontroller.
The operating mode:
- When the sensor is blocked, the DO output is high
- The AO signal is not enabled in this module
- Power supply: 3.3-5V
- Power consumption current 20 mA max
- PCB dimensions: 32 x 14 mm

A set of flat drive belts with a diameter from 27mm to 80mm. The kit includes approximately 50 pieces of strips from 0.5 mm to 1 mm thick.
Technical data:
- width: 4.0mm
- diameter from 27mm to 80mm
- thickness: from 0.5 to 1mm
Quantity tolerance +/- 5%

This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.
The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.
Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features:
- Interfaces:
       -I2C (up to 3.4 MHz)
       -SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
       - Temperature: -40ºC to + 85ºC
0-100%
       - Pressure: 300-1100 hPa
- Resolution of the measures:
       - Temperature: 0.01ºC

This product is a BNC probe with double black and red crocodile plug to perform your oscilloscope tests.
Its internal resistance is 75 ohm and it has a length of one meter. BNC Probe Male Double Crocodile Plug features:
- 100% new and high quality
- New BNC to double crocodile clip oscilloscope probe
- Standard BNC ends can be used for all oscilloscopes
- Length: 100 cm
- Coaxial cable 3c-2v 75 ohm
- Includes 11 crocodile cable