Arduino compatible Mega2560 R3 CH340 board
  • Arduino compatible Mega2560 R3 CH340 board

Arduino compatible Mega2560 R3 CH340 board

B0015

Version compatible with Arduino Mega2560 R3
It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader
With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports)
The board includes a USB connector, an ICSP port , a reset button and some status LEDs
Arduino compatible Mega2560 R3 CH340 board features:

- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Digital I / O Pins: 54 (14 PWM outputs)
- Analog input pins 16
- DC current per I / O Pin 40 mA
- DC Current per Pin 3.3V 50 mA
- Flash: 256 KB of which 8 KB are used by the bootloader
- SRAM: 8 KB
- EEPROM: 4 KB - Clock speed 16 MHz

OEM
5905323231009
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Arduino compatible Mega2560 R3 CH340 board description

Version compatible with Arduino Mega2560 R3
It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader
With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports)
The board includes a USB connector, an ICSP port , a reset button and some status LEDs

Arduino compatible Mega2560 R3 CH340 board features:



- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Digital I / O Pins: 54 (14 PWM outputs)
- Analog input pins 16
- DC current per I / O Pin 40 mA
- DC Current per Pin 3.3V 50 mA
- Flash: 256 KB of which 8 KB are used by the bootloader
- SRAM: 8 KB
- EEPROM: 4 KB < br /> - Clock speed 16 MHz
- USB communication - CH340

Customers who bought this product also bought

40x Male to male cables 20cm

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use

K0006

Price €2.06

IR Remote Control + IR Infrared Receiver VS1838

IR Remote Control + IR Infrared Receiver VS1838 features:
- The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal
- Vcc supply: 3.3V-5V
- IN digital output to connect to the port Arduino I / O
- Remote measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module
- Light a 3mm red LED by Infrared

W0021

Price €2.06

XL6009 DC-DC Step-Up Booster Controller LM2577

- The XL6009 module has a superior performance than the LM2577 module
- The regulator-booster of High performance
Characteristic:
- Based on the XL6009E1 regulator
- Input voltage: 3V-32V,
- Output voltage: 5-35V (adjustable),
- Output current: 2A maximum 3A (heat sink is required)
- Conversion efficiency: up to 94%
- Rectifier: not synchronous rectification
- Short circuit protection: current limitation, since recovery
- Operating temperature: industrial grade (-40 ° C - 85 ° C)
- Load regulation: ± 0.5%
- Voltage regulation: ± 0.5%
- Size: 50 x 22 x 15 mm

A0005

Price €2.02

Sensor Module Moisture Earth Water Soil

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

S0021

Price €1.61

5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

R0038

Price €2.44
€21.40

21,40 tax excl.

1
Last item
Price €21.40

Order until 4pm we will send today
30 days return