Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €4.55
Push button 6x6x5mm 2pins Push button 6x6x4mm features: -Touch Push Tact Switch mini electronic Arduino push button -Measures: 6x6x45mm -Quantity: 1 unit Code K0269 Available Price €0.20
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.62
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 ✗ Out-of-Stock Price €3.55
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.15
Screen OLED 0.96" 128x64 Blue I2C It is a monochrome OLED display module with a 128x64 resolution dot matrix and an IC2 interface. Compared to the LCD, OLED displays are Much more competitive, they have a number of advantages such as high brightness, self-emission, high contrast ratio, wide viewing angle, wide temperature range, and low power consumption. Screen OLED 0.96" 128x64 Blue I2C features: - Interface: I2C (logical level 3.3V) - Resolution: 128 x 64 - Angle of view: & gt; 160 degree - Screen color: blue - Screen Dimension: 2.43cm / 0.96 " - IC Controller: SSD1306 - Power supply: 3.3V - 5VDC - Operating temperature: -20 - 70 - Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 " Code P0096 Available Regular price €5.37 -€1.51 Price €3.86
Sensor Shield V5 APC220 Arduino compatible Arduino Sensor Shield V5 APC220 features: Sensor Shield V5.0 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more Code M0001 Available Price €2.39
USB Digital Power Voltmeter Tester Amps Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets ...USB Digital Power Voltmeter Tester Amps features:- Operating range: voltage 3.5 - 9V- Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%- Dimensions: 60 x 23 x 19mm Code K0083 Available Price €4.92
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.44
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €4.95
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.44
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €21.32 -€2.00 Price €19.32
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.44
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €4.95
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.44
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €21.32 -€2.00 Price €19.32
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94