Breadboard Power Supply Protoboard 830/400 Points MB102 Ideal for your electronic projects, arduino, but can also be used with other microcontrollers. Breadboard Power Supply Protoboard 830/400 Points MB102 features:- Input voltage supports up to 12V- Selectable 3.3V or 5V- USB input or standard DC 2.1 x5.5mm connector- Maximum current 700mA- It fits perfectly on the MB-102 breadboard feeding the two lateral buses- Weight: 15 gr. (approx.) Compatible only with MB-102 type plates Code A0003 Available Price €1.61
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
Motor Nema 17 1.22kg 17HS2408 Characteristic: - Motor passes 1.8º (200 steps per turn) - Capable of loading 1.22 kg / cm Code I0065 Available Price €7.43
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57
Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use features: Code PP049 Available Price €4.95
Blue 3D Pen and PLA Set of 20 colors Filament 1.75mm x 5m Blue 3D Pen and PLA Set of 20 colors Filament 1.75mm x 5m features:- White- Gray- Yellow- Orange- Red- Blue- Green- Black- Pink- Purple- Luminescent green- Gold- Silver- Transparent purple- Transparent blue- Transparent orange- 4 random colors Code I0303 ✗ Out-of-Stock Price €24.79
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.31
PLA Filamento 1.75mm 0.85kg MasterSpool recarga color azul Premium Bobina para Impresora 3D Code I0486 Available Regular price €13.14 -15% Price €11.17
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €4.95
TB6600 4.5A Single Axis CNC Controller The output current of this controller is infinitely adjustable to meet the various requirements of your application.It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.Its large heat sink allows good quality cooling.The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features: - Operating voltage DC 10V-45V- Maximum nominal output: 4.5 A- DC32V switching power is recommended- 6N137 high speed optical coupling, ensure high speed without losing step Code I0151 Available Regular price €11.49 -€1.00 Price €10.49
Mechanical Ender 3 / 5 / CR 10 / 20 X Pro 3D Printer Mechanical Ender 3 5 CR 10 20 X Pro 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Compatible with Ender-3 series, CR-10 series, etc. - PCB dimensions: 18mm x 18mm Code I0178 Available Price €3.10
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €6.90 -10% Price €6.21
IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features: - For Hot Bed Ramps- Package: TO-220- Quantity: 1 unit with heatsink and screw Code I0092 Last items in stock Price €2.06
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer kit for Arduino CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features: - Content:* 1x UNO R3 CH340 Compatible with Arduino* 1x CNC Shield V3* 4x A4988 Drivers* 4x Heatsinks for A4988* Jumpers Code I0010 Available Regular price €14.74 -€0.74 Price €14.00
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.27
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €4.95
TB6600 4.5A Single Axis CNC Controller The output current of this controller is infinitely adjustable to meet the various requirements of your application.It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.Its large heat sink allows good quality cooling.The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features: - Operating voltage DC 10V-45V- Maximum nominal output: 4.5 A- DC32V switching power is recommended- 6N137 high speed optical coupling, ensure high speed without losing step Code I0151 Available Regular price €11.49 -€1.00 Price €10.49
Mechanical Ender 3 / 5 / CR 10 / 20 X Pro 3D Printer Mechanical Ender 3 5 CR 10 20 X Pro 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Compatible with Ender-3 series, CR-10 series, etc. - PCB dimensions: 18mm x 18mm Code I0178 Available Price €3.10
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €6.90 -10% Price €6.21
IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features: - For Hot Bed Ramps- Package: TO-220- Quantity: 1 unit with heatsink and screw Code I0092 Last items in stock Price €2.06
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer kit for Arduino CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features: - Content:* 1x UNO R3 CH340 Compatible with Arduino* 1x CNC Shield V3* 4x A4988 Drivers* 4x Heatsinks for A4988* Jumpers Code I0010 Available Regular price €14.74 -€0.74 Price €14.00
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.27