Industrial DKC-1A stepper motor controller

MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply.

Zum Scanner Expansion Board 3D DIY features:
- Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- 3D Scanner Ciclop is an open source project created by bq
- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser
- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 5A Stepper Motor Driver Board features:
- Minimum operating voltage: 12 V
- Maximum operating voltage: 48 V
- Maximum current: ± 5 A
- Maximum power: 240W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs optically isolated
- Step resolution: 200, 400, 1600, 3200
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 adjustable by interruptor DIP
- Current control: 0.2A/0.6A/1.2A/1.8A/2.5A/3.3A/4.2A/>

CNC shield for arduino works as a controller for CNC type milling machines,
3D printers, laser cutters .
CNC Shield Expansion Plate V3 Engraver 3D Printer features:

• 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible
• 4 support axes X, Y, Z, A
• 2 limit switches for each axis (6 in total)

5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features:
- Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software.
- Designed for single axis CNC single phase stepper controller controller:
M542, MA860H, 2M542, DM860 etc.
- Stepper motor controller drivers 5 axis maximum support.
- Wide input voltage range: 12-24V and with anti-reverse function.
- USB power supply and peripheral power phase are separated to protect computer security
- All signals are opto-isolated, which can protect the security of your computer.
- 5 input interface to define limit, emergency stop, cutter alignment, etc.
- A relay output control interface, accessed by spindle motor or air pump, water pump, etc.

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features:
- 100% brand new and high quality
- Optical detector: TCST2103
- Length cable: 50cm
- Size: 32mm x 10mm

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

Contented:
- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino
- 1x CNC Shield V3
- 4x A4988 Drivers
- 4x Heatsinks for A4988
- USB Cable
- Jumpers