3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper

Mechanical End of Career CNC Ramps1.4 3D Printer features:
- Mechanical limit switch, Endstop
- 100% brand new and high quality
- 1A 125V AC switch - Cable length: 70cm
- PCB dimensions: 40mm x 15mm

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers.

RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

CNC shield for arduino works as a controller for CNC type milling machines,
3D printers, laser cutters .
CNC Shield Expansion Plate V3 Engraver 3D Printer features:

• 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible
• 4 support axes X, Y, Z, A
• 2 limit switches for each axis (6 in total)

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply.

Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features:
- Superior performance of MOSFET
- Maximum current - up to 30A (heat sink)
- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series
- To control - 5-24V digital signal

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink

Compared to the TMC2100 module, the TMC2208 controller module emits less heat.