3x Heat Sink Aluminium Adhesive A4988 DRV8825 3x Heat Sink Aluminium Adhesive A4988 DRV8825 features: - Package includes: 3x Heatsink with adhesive - Ideal for DRV8825, A4988 etc - Dimensions: 9 x 9 x 5mm Code I0046 Available Price €0.35
Motor Nema 17 4.28kg 17HS4401 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! Code I0020 Available Regular price €11.50 -€1.55 Price €9.95
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
Power supply DC 12V 16.7A 200W Power supply DC 12V 16.7A 200W features: - Supply voltage: 110 / 230V AC - Output voltage: 12V DC - Output amperage: 16.7A - Power at 12V: 200W - Dimensions: 200mm x 99mm x 43mm - IP20 ROHS CE Code A0057 Available Price €16.99
PCB Heated Bed MK3 Alu 3mm 12V 24V 3D Printer PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer features: - Similar to MK2, can also be used with 12 volts or 24 volts - Measurements: 214 x 214 mm - 1 layer of 35μm (1 oz base) of copper Code I0091 Available Price €11.99
Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 100.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0092 Available Price €0.35
Kapton type 10mm thermal tape Characteristic: - Supports up to 280ºC - Electrical and antistatic insulation - Resistant to acid and alkaline products - Resistant to solvent - Adhesive - Length Approx: 33m - Polyamide adhesive tape 10mm - Known as Kapton polyamide tape - Product for welding works on those that need to protect some component from the heat Code I0061 Available Price €2.15
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
Router TB6600 1 Axis 3.5A Stepper Motor Driver Board Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features: - Minimum operating voltage: 9 V- Maximum operating voltage: 40 V- Maximum current: ± 3.5 A- Maximum power: 160W- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23- Control inputs 5V optically isolated- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP- Current control: 0.5A/>0A/> Code I0159 Available Price €10.90
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
Router TB6600 1 Axis 5A Stepper Motor Driver Board Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.Run easily with Arduino. Router TB6600 1 Axis 5A Stepper Motor Driver Board features: - Minimum operating voltage: 12 V- Maximum operating voltage: 48 V- Maximum current: ± 5 A- Maximum power: 240W- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23- Control inputs optically isolated- Step resolution: 200, 400, 1600, 3200- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 adjustable by interruptor DIP- Current control: 0.2A/0.6A/1.2A/1.8A/2.5A/3.3A/4.2A/> Code I0160 Available Regular price €18.49 -€1.50 Price €16.99
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €9.49
Mechanical End of Career CNC Ramps1.4 3D Printer Mechanical End of Career CNC Ramps1.4 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Cable length: 70cm - PCB dimensions: 40mm x 15mm Code I0029 Available Price €1.49
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
UNO R3 Atmega 328P + CNC Shield + 4x A4988 Stepstick Contented:- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino- 1x CNC Shield V3- 4x A4988 Drivers- 4x Heatsinks for A4988- USB Cable- Jumpers Code I0002 Available Regular price €20.30 --€1.84 Price €22.14
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €9.49
Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features: - 100% brand new and high quality - Optical detector: TCST2103 - Length cable: 50cm - Size: 32mm x 10mm Code I0024 Available Price €1.49
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €3.49
Router TB6600 1 Axis 3.5A Stepper Motor Driver Board Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features: - Minimum operating voltage: 9 V- Maximum operating voltage: 40 V- Maximum current: ± 3.5 A- Maximum power: 160W- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23- Control inputs 5V optically isolated- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP- Current control: 0.5A/>0A/> Code I0159 Available Price €10.90
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
Router TB6600 1 Axis 5A Stepper Motor Driver Board Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.Run easily with Arduino. Router TB6600 1 Axis 5A Stepper Motor Driver Board features: - Minimum operating voltage: 12 V- Maximum operating voltage: 48 V- Maximum current: ± 5 A- Maximum power: 240W- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23- Control inputs optically isolated- Step resolution: 200, 400, 1600, 3200- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 adjustable by interruptor DIP- Current control: 0.2A/0.6A/1.2A/1.8A/2.5A/3.3A/4.2A/> Code I0160 Available Regular price €18.49 -€1.50 Price €16.99
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €9.49
Mechanical End of Career CNC Ramps1.4 3D Printer Mechanical End of Career CNC Ramps1.4 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Cable length: 70cm - PCB dimensions: 40mm x 15mm Code I0029 Available Price €1.49
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
UNO R3 Atmega 328P + CNC Shield + 4x A4988 Stepstick Contented:- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino- 1x CNC Shield V3- 4x A4988 Drivers- 4x Heatsinks for A4988- USB Cable- Jumpers Code I0002 Available Regular price €20.30 --€1.84 Price €22.14
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €9.49
Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features: - 100% brand new and high quality - Optical detector: TCST2103 - Length cable: 50cm - Size: 32mm x 10mm Code I0024 Available Price €1.49
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €3.49