Heated Bed PCB MK2B 3D Reprap Printer Heated Bed PCB MK2B 3D Reprap Printer features: - Measurements: 214mm x 214mm Code I0001 Available Regular price €6.91 -€2.00 Price €4.91
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.23
Dupont Connector 2.54mm Male Dupont Connector 2.54mm Male features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0111 Available Price €1.81
Vertical Slide Switch 2P2T 50V 0.5A 6 DIP pins and 2 positions DPDT. This switch is widely used to control the operation of many small electronic power projects, including volume and other controls for audio video, dimmer controls for lights.It is also a great component for DIY. Vertical Slide Switch 2P2T 50V 0.5A features: - Type: 2P2T- Contact resistance: 30 MΩ max.- Insulation resistance: 100 MΩ- Maximum operating voltage: 50V- Maximum operating current: 0.5A- Can support 500 VAC for 1 minute- Step between pins: 2.54mm / 0.1 "- Pin size: 4.5x0.5x15 / 0.77 "x0.19"- Type of current: DC- Pins to be welded- Switch action: 2 ON / OFF positions- Shape of interrupter: rectangular- Size: 16x6.5x15 / 0.2 "x0.02" Code K0104 Available Price €0.40
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
Female DC Power Connector Jack 2.1x5.5mm Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Female DC Power Connector Jack 2.1x5.5mm features: - Ideal for connecting without welding- It has two screws in the tip for positive and negative cable screwdriver Code K0050 Available Price €0.40
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.06
Motor Nema 17 4.28kg 17HS4401 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! Code I0020 ✗ Out-of-Stock Regular price €9.50 -€1.55 Price €7.95
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.27
UNO R3 Atmega 328P + CNC Shield + 4x A4988 Stepstick Contented:- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino- 1x CNC Shield V3- 4x A4988 Drivers- 4x Heatsinks for A4988- USB Cable- Jumpers Code I0002 Last items in stock Regular price €16.78 --€1.52 Price €18.30
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57
DM556 Stepper motor controller 5.6A 50V The DM556 low-voltage digital stepper motor controller, which uses the latest 32-bit DSP technology, is suitable for driving the 57 and 86 series motors Nema23, with excellent low-speed performance to meet the application needs of small and medium-sized equipment. Code I0149 Last items in stock Price €23.55
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.57
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.09
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €2.88
Mechanical End of Career CNC Ramps1.4 3D Printer Mechanical End of Career CNC Ramps1.4 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Cable length: 70cm - PCB dimensions: 40mm x 15mm Code I0029 Available Price €1.23
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.27
UNO R3 Atmega 328P + CNC Shield + 4x A4988 Stepstick Contented:- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino- 1x CNC Shield V3- 4x A4988 Drivers- 4x Heatsinks for A4988- USB Cable- Jumpers Code I0002 Last items in stock Regular price €16.78 --€1.52 Price €18.30
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57
DM556 Stepper motor controller 5.6A 50V The DM556 low-voltage digital stepper motor controller, which uses the latest 32-bit DSP technology, is suitable for driving the 57 and 86 series motors Nema23, with excellent low-speed performance to meet the application needs of small and medium-sized equipment. Code I0149 Last items in stock Price €23.55
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.57
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.09
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €2.88
Mechanical End of Career CNC Ramps1.4 3D Printer Mechanical End of Career CNC Ramps1.4 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Cable length: 70cm - PCB dimensions: 40mm x 15mm Code I0029 Available Price €1.23
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57