Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module

Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features:
- 100% brand new and high quality
- Optical detector: TCST2103
- Length cable: 50cm
- Size: 32mm x 10mm

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

Router TB6560 1 Axis 3A Stepper Motor Driver Board features:
- Minimum operating voltage: 10 V
- Maximum operating voltage: 35 V (24V recommended)
- Maximum current: ± 3 A
- Stepper motor · two phases · four phases
- Resolution of microsteps: full, 1/2, 1/8, and 1/16
- PCB measurements: 75x50 mm
- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board
- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply
- 6N137 high speed optical coupling guarantees high speed without losing steps
- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent
- Protection circuit to ensure optimal performance
- Maximum nominal output: 3 A, peak 3.5A

A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details.

Contented:
- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino
- 1x CNC Shield V3
- 4x A4988 Drivers
- 4x Heatsinks for A4988
- USB Cable
- Jumpers

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.
It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.
Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features:
- Operating voltage: 5-32 VDC
- Signal entry point for the lower level entry
- Optimization of the acceleration of the S curve
- The maximum output frequency can reach 20 KHz

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 5A Stepper Motor Driver Board features:
- Minimum operating voltage: 12 V
- Maximum operating voltage: 48 V
- Maximum current: ± 5 A
- Maximum power: 240W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs optically isolated
- Step resolution: 200, 400, 1600, 3200
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 adjustable by interruptor DIP
- Current control: 0.2A/0.6A/1.2A/1.8A/2.5A/3.3A/4.2A/>

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm