Potentiometer B100K linear Characteristic: -100k OHM kΩ - Linear potentiometer 100k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0070 Available Price €0.82
Vertical Slide Switch 2P2T 50V 0.5A 6 DIP pins and 2 positions DPDT. This switch is widely used to control the operation of many small electronic power projects, including volume and other controls for audio video, dimmer controls for lights.It is also a great component for DIY. Vertical Slide Switch 2P2T 50V 0.5A features: - Type: 2P2T- Contact resistance: 30 MΩ max.- Insulation resistance: 100 MΩ- Maximum operating voltage: 50V- Maximum operating current: 0.5A- Can support 500 VAC for 1 minute- Step between pins: 2.54mm / 0.1 "- Pin size: 4.5x0.5x15 / 0.77 "x0.19"- Type of current: DC- Pins to be welded- Switch action: 2 ON / OFF positions- Shape of interrupter: rectangular- Size: 16x6.5x15 / 0.2 "x0.02" Code K0104 Available Price €0.40
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.This product offers more flexible options for users.MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.se high quality MOSFET, better cooling and more stable. Code I0143 Backorder Regular price €26.36 -€2.00 Price €24.36
Pulley GT2 20 Teeth 5mm Aluminium Pulley 3D Printer Pulley GT2 20 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 20 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 18mm - Inner hole: 5mm - Use with strap: 6mm and 6.35mm - Ideal to fix on the axis of the motors of your 3D printer Code I0031 Available Price €1.48
Blue Flat Steel and Plastic Screwdriver Philips blue flat screwdriver made of steel and plastic suitable for screws with 2.0mm head for electronic applications. Code H0126 Available Price €0.40
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €2.88
LED Diode Assortment 5mm red, green, yellow pack 15 pcs LED Diode Assortment Kit 15 pcs 5mm red, green, yellow features:- Lens color: red, green, yellow - diffuse- Size: 5mm- Operating current: 20mA- Voltage (red) 1,8V-2,3V- Voltage (green) 3,2V-3,4V- Voltage (yellow) 1,8V-2,3V- Anode (A): Positive (long leg): 28mm- Catode (K): Negative (short leg): 25mm - Operating temperature: -25ºC/80ºC- Welding temperature: +260ºC - Quantity: 30 units*5x red*5x green*5x yellow Code P0160 Available Price €0.82
3S BMS 25A 12.6V 18650 PCM PCB Circuit Charging Module. In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0106 Available Price €3.71
CNC Shield Expansion Plate + 4x A4988 Stepstick 3D Printer A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details. Code I0105 ✗ Out-of-Stock Price €8.55
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Last items in stock Price €4.09
Industrial DKC-1A stepper motor controller The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features: - Operating voltage: 5-32 VDC- Signal entry point for the lower level entry- Optimization of the acceleration of the S curve- The maximum output frequency can reach 20 KHz Code M0155 Available Price €7.02
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Last items in stock Price €4.09
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 ✗ Out-of-Stock Price €10.32
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €7.84
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €17.27
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 ✗ Out-of-Stock Price €1.57
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57
CNC Shield Expansion Plate + 4x A4988 Stepstick 3D Printer A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details. Code I0105 ✗ Out-of-Stock Price €8.55
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Last items in stock Price €4.09
Industrial DKC-1A stepper motor controller The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features: - Operating voltage: 5-32 VDC- Signal entry point for the lower level entry- Optimization of the acceleration of the S curve- The maximum output frequency can reach 20 KHz Code M0155 Available Price €7.02
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Last items in stock Price €4.09
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 ✗ Out-of-Stock Price €10.32
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €7.84
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €17.27
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 ✗ Out-of-Stock Price €1.57
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57