Mechanical Ender 3 / 5 / CR 10 / 20 X Pro 3D Printer

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

Router TB6560 1 Axis 3A Stepper Motor Driver Board features:
- Minimum operating voltage: 10 V
- Maximum operating voltage: 35 V (24V recommended)
- Maximum current: ± 3 A
- Stepper motor · two phases · four phases
- Resolution of microsteps: full, 1/2, 1/8, and 1/16
- PCB measurements: 75x50 mm
- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board
- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply
- 6N137 high speed optical coupling guarantees high speed without losing steps
- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent
- Protection circuit to ensure optimal performance
- Maximum nominal output: 3 A, peak 3.5A

Auto shut down module for MKS GEN L SKR V1.3 

MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. 

5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features:
- Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software.
- Designed for single axis CNC single phase stepper controller controller:
M542, MA860H, 2M542, DM860 etc.
- Stepper motor controller drivers 5 axis maximum support.
- Wide input voltage range: 12-24V and with anti-reverse function.
- USB power supply and peripheral power phase are separated to protect computer security
- All signals are opto-isolated, which can protect the security of your computer.
- 5 input interface to define limit, emergency stop, cutter alignment, etc.
- A relay output control interface, accessed by spindle motor or air pump, water pump, etc.

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details.

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

Contented:
- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino
- 1x CNC Shield V3
- 4x A4988 Drivers
- 4x Heatsinks for A4988
- USB Cable
- Jumpers

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers

Mechanical End of Career CNC Ramps1.4 3D Printer features:
- Mechanical limit switch, Endstop
- 100% brand new and high quality
- 1A 125V AC switch - Cable length: 70cm
- PCB dimensions: 40mm x 15mm