Micro Servo 9g SG90

A slip ring capable of holding up to 6 wires of 22mm diameter.

DC Gear Motor N20 200 RPM 12V DIY Robot features:
- Voltage: 12V
- Speed of rotation: 200RPM
- Motor dimensions:
* Diameter 12 mm
* Height 24 mm
- For Arduino, Smart Car, Robotics, Fans, Appliances

The 28BYJ-48 has everything you need to start using stepper motors in your project. A stepper motor converts digital impulses into small movement steps. in one direction Characteristic: - Motor model: 28BYJ-48
- Motor phases: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per lap: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm
- Operating temperature: -45ºC to + 125ºC
- Motor cable length: 19cm
- Motor block diameter: 28mm
- Motor dimensions: 42mm x 32mm x 30mm

9g digital servo new version of SG90.
POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque.
It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features:
Weight: 9g
Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v)
Gear type: POM with carbon fiber
Operating speed: 0.1sec /60degree (4.8v)
Temperature range: 0„ƒ_ 55„ƒ
Dead band width:1us
servo wire length: 25 cm
Servo Plug: JR (Fits JR and Futaba)
servo arms &screws included and fit with Futaba servo arm

For Arduino, Smart Car, Robotics.
Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features:
- Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm
- Max speed: 12000rpm
- Weight: 16.5 g

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

Servo Motor Type S3003 Aeromodelling features:
- Operating voltage: 4.8 V to 6 V
- Max torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degree (4.8V), 0.19sec / 60 degree (6V)
- Max radius: 180 ° (90º in each direction)
- Temperature range: - 20 + 60 C degrees
- Weight: 38 g
- Cable length: 26cm
- Dimensions: 40.5 x39x 20 mm
- Servo connector: JR - Chinese Manufacture

the robot car motor holder and assembly accessories

Mounting Bracket for Nema Engine 17 42mm features:
- Steel bracket for PAP Nema 17 3D printer motor
- Mounting bracket of 42mm L shape alloy steel for The NEMA17 3D Stepper Motor Printer
- Material: Alloy Steel - Size: 5 x 5 x 5cm
- Black Color
- Fit for 42mm Stepper Motor as NEMA17