Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.07
Screen OLED 0.96" B 128x64 Yellow-Blue SPI/I2C Screen OLED 0.96" B 128x64 Yellow-Blue SPI/I2C features: - Oled 0.96 "128 * 64 pixel display - One yellow line and 3 blue lines - Drive IC model SDD1306 - Power supply: 3V-5.5V - View angle: 160 degrees - SPI interface (I2C can be changed) - Low consumption 0.08W - Temperature usage: -20 to 70 ºC - PCB board dimension: 32 x 32 mm - OLED technology offers high contrast, significantly improves black on the screen and energy efficiency - very low consumption of energy. Code P0025 Available Price €6.44
Raspberry Pi Pico The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython. Code RA124 Available Price €4.12
Protoboard GPIO T-type Extension Board for Micro:Bit Connect this extension board to the micro: bit development board, then they can be directly connected to the breadboard. Code RA043 ✗ Out-of-Stock Price €6.20
ADXL345 3-Axis Accelerometer SPI and I2C Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features: - Type: 3-axis accelerometer- Chip: ADXL345- Supply voltage: 3-5V- Consumption: 40uA active and 0.1uA on hold- Communication: SPI and I2C- Measurements: Static and dynamic acceleration- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g- Resolution: 13 bits- Dimensions: 20x16mm- Operating temperature: -40 °C to +80 °C- Detection: Free fall, click-double click Code M0018 Available Price €2.55
45cm Crocodile to USB Male Test Cable 45-centimetre crocodile cables to USB. They come in a pair of two cables, one red and the other black, connected to a male USB connector. Code K0317 Available Price €2.31
GY-91 10DOF 4 Sensors in 1 Module with MPU-9250 and BMP280 This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB). Code M0079 ✗ Out-of-Stock Price €13.18
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €6.60
High Power LED Chip Diode 10W Blue SMD COB COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light - Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little thermal silicone in each of the placement centers of the diodes- The thermal paste increases the thermal transfer between the diode and the metal plate used as circuit Code P0033 Available Price €2.34
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.81
Strip WS2812B 5m 30 LED /m white RGB RGB LEDs WS2812B WS2812B are LEDs that have integrated logic, so it is possible to vary the color of each LED individually. WS2812B includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. 30 individually indexable LEDs. 24-bit color control (8-PWM) -bit per channel) 16.8 million colors per LED One-wire communication Power: 5 V Width: 11 mm Thickness: 2.6 mm Length: 5 meters Consumption: 1.8A (all white) Waterproof With 3M adhesive Input and output terminals (data and power) Links https://learn.adafruit.com/adafruit-neopixel-uberguide/> Code P0106 Available Regular price €32.98 -€10.00 Price €22.98
40 LED RGB Digital Panel Adafruit Neopixel with Connectors 5050 Matrix 4 RGB LED panel with digital control to be connected in cascade to complete the reception and decoding of the data.The light emitted is very powerful and millions of colors can be generated thanks to the RGB device. 40 LED RGB Digital Panel Adafruit Neopixel with Connectors 5050 Matrix features: - 40 individually addressable RGB LEDs (NeoPixels based on SK6812 or WS2812B) arranged in a 5 × 8 matrix- 24-bit color control (8-bit PWM per channel); 16.8 million colors per pixel- The digital control interface of a single cable requires only one Arduino pin (the default pin can be customized)- Operating voltage range: 4 V to 6 V (connected to the 5 V Arduino rail by default) Code P0133 Available Price €8.22
LED strip Warm white 12V 3528 5m /300 Strip of 300 warm white coloured LED lights, 5 metres long. Code K0284 Available Price €9.05
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.09
LED Lighting Chain WS2811 Pixels Digital Addressable RGB 50LED 5V IP68 This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually. WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background Easy programming with Arduino, ESP32, ESP8266, etc. Code P0164 Available Regular price €13.18 -15% Price €11.20
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.81
LED Diode 1W Warm White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 2.85-3.85V - Current: 350mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0151 Last items in stock Price €0.81
LED strip cold white 12V 3528 5m /300 Strip of 300 cold white coloured LED lights, 5 metres long. Code K0593 Available Price €9.05
High Power LED Chip Diode 10W Blue SMD COB COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light - Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little thermal silicone in each of the placement centers of the diodes- The thermal paste increases the thermal transfer between the diode and the metal plate used as circuit Code P0033 Available Price €2.34
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.81
Strip WS2812B 5m 30 LED /m white RGB RGB LEDs WS2812B WS2812B are LEDs that have integrated logic, so it is possible to vary the color of each LED individually. WS2812B includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. 30 individually indexable LEDs. 24-bit color control (8-PWM) -bit per channel) 16.8 million colors per LED One-wire communication Power: 5 V Width: 11 mm Thickness: 2.6 mm Length: 5 meters Consumption: 1.8A (all white) Waterproof With 3M adhesive Input and output terminals (data and power) Links https://learn.adafruit.com/adafruit-neopixel-uberguide/> Code P0106 Available Regular price €32.98 -€10.00 Price €22.98
40 LED RGB Digital Panel Adafruit Neopixel with Connectors 5050 Matrix 4 RGB LED panel with digital control to be connected in cascade to complete the reception and decoding of the data.The light emitted is very powerful and millions of colors can be generated thanks to the RGB device. 40 LED RGB Digital Panel Adafruit Neopixel with Connectors 5050 Matrix features: - 40 individually addressable RGB LEDs (NeoPixels based on SK6812 or WS2812B) arranged in a 5 × 8 matrix- 24-bit color control (8-bit PWM per channel); 16.8 million colors per pixel- The digital control interface of a single cable requires only one Arduino pin (the default pin can be customized)- Operating voltage range: 4 V to 6 V (connected to the 5 V Arduino rail by default) Code P0133 Available Price €8.22
LED strip Warm white 12V 3528 5m /300 Strip of 300 warm white coloured LED lights, 5 metres long. Code K0284 Available Price €9.05
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.09
LED Lighting Chain WS2811 Pixels Digital Addressable RGB 50LED 5V IP68 This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually. WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background Easy programming with Arduino, ESP32, ESP8266, etc. Code P0164 Available Regular price €13.18 -15% Price €11.20
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.81
LED Diode 1W Warm White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 2.85-3.85V - Current: 350mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0151 Last items in stock Price €0.81
LED strip cold white 12V 3528 5m /300 Strip of 300 cold white coloured LED lights, 5 metres long. Code K0593 Available Price €9.05