Mini Submersible Water Pump DC 3V 120L/H Characteristic: - Operating voltage: 3-6V - Max flow: 80-120 l / h - Maximum pumping height: 40-110cm - Continuous working time of 500 hours - Cable length: 20cm - Inside outlet diameter: 5 mm - Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm Code M0040 ✗ Out-of-Stock Regular price €2.06 -€0.51 Price €1.55
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
Rechargeable Battery Sanyo NCR18650GA 3450mAh Li-ion 3,6V 10A Characteristic: - Lithium Battery WITHOUT Protection - Nominal capacity: 3450mAh (0.2C, discharge of 2.5V) - Minimum capacity: 3350mAh (0.2C, 2.5V discharge) - Charging voltage: 4.2 ± 0.05 V - Nominal voltage: 3.6V - Charging method: DC-CV (constant voltage with current limited) - Charging current: standard charge: 1675mA, - Max. Discharge current: 10A (ambient temperature 25 °) - Charging time: standard charge: 4 hours, - Discharge cut-off voltage: 2.5V - Cell weight: 47g maximum - Cell dimension: Height: 65.30 mm maximum, Diameter: 18.50 mm maximum Code PP031 ✗ Out-of-Stock Price €7.85
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.12
LED 5mm RGB Common Anode LED 5mm RGB 4 Pin anode commun with clear water lens. Code P0019 Available Price €0.17
PLA Set of 20 colors Filament 1.75mm x 5m PLA Set of 20 colors Filament 1.75mm x 5m features:- White- Gray- Yellow- Orange- Red- Blue- Green- Black- Pink- Purple- Luminescent green- Gold- Silver- Transparent purple- Transparent blue- Transparent orange- 4 random colors Code I0301 ✗ Out-of-Stock Price €9.67
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.61
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.22 -€0.20 Price €2.02
Micro Motor 3V 5V 6V DC DIY for Arduino UNO Mega Robotics For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC DIY Arduino UNO Mega Robotics features: - Operating voltage: 1.5V to 6V- DC current: 350mA- Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0037 Available Price €0.81
Motor Nema 17 42HS482504 2.5A One of the most popular stepper motors with 200 steps per revolution and a maximum load of 5 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices! Code I0126 Available Price €12.31
Slip ring 22mm diameter 6 wires A slip ring capable of holding up to 6 wires of 22mm diameter. Code R0093 ✗ Out-of-Stock Price €24.38
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Regular price €7.40 -€1.00 Price €6.40
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.40
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
Geared Motor with Encoder 6V 1:120 for Arduino Smart Car Robot Geared Motor with Encoder 6V 1120 Arduino Smart Car Robot features:- Voltage: 3 to 6Vdc- Speed without load: 200 RPM to 6Vdc- No-load current: 110mA at 3Vdc - 250mA at 6Vdc- Reductive: 1: 120 Code R0043 Available Price €2.85
5V Stepper Motor 28BYJ-48 + ULN2003 Driver The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.44
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.22 -€0.20 Price €2.02
Micro Motor 3V 5V 6V DC DIY for Arduino UNO Mega Robotics For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC DIY Arduino UNO Mega Robotics features: - Operating voltage: 1.5V to 6V- DC current: 350mA- Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0037 Available Price €0.81
Motor Nema 17 42HS482504 2.5A One of the most popular stepper motors with 200 steps per revolution and a maximum load of 5 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices! Code I0126 Available Price €12.31
Slip ring 22mm diameter 6 wires A slip ring capable of holding up to 6 wires of 22mm diameter. Code R0093 ✗ Out-of-Stock Price €24.38
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Regular price €7.40 -€1.00 Price €6.40
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.40
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
Geared Motor with Encoder 6V 1:120 for Arduino Smart Car Robot Geared Motor with Encoder 6V 1120 Arduino Smart Car Robot features:- Voltage: 3 to 6Vdc- Speed without load: 200 RPM to 6Vdc- No-load current: 110mA at 3Vdc - 250mA at 6Vdc- Reductive: 1: 120 Code R0043 Available Price €2.85
5V Stepper Motor 28BYJ-48 + ULN2003 Driver The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.44