10x Linear Potentiometers 2k OHM kΩ

The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4.
It has 9 digital input / output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery and a power button. restart
It contains everything necessary to support the microcontroller; simply connect it to a computer with a USB cable or a battery to start.
The LilyPad Arduino USB differs from previous LilyPad cards in that the ATmega32U4 has built-in USB communication, eliminating the need for a separate USB to serial adapter. This allows the LilyPad Arduino USB to appear on a connected computer as a mouse and keyboard, as well as a virtual serial / COM (CDC) port.

Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino features:
-Micro KW12-3 on / off switch
-Max Current: 5A -AC voltage: 125-250V
-Operating temperature: -40 to 70 degrees C
-Quantity: 2 units

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually.
WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually.
For this reason, these types of LEDs are called individually indexable.
They are based on the 5050 LED. 

0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display features:
- Interface: I2C (logical level 3.3V)
- Resolution: 128x64
- Angle of view:> 160 degrees
- Screen color: blue and yellow (1/4 above yellow and 3/4 below blue)
- Screen Dimension: 2.43cm / 0.96 "
- IC Controller: SSD1306
- Power supply: 3.3V - 5VDC
- Operating temperature: -20 ° C - 70 ° C
- Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 "
- Application: smart watch, MP3, thermometer, instruments, DIY projects, etc ...
- It is an OLED screen module with blue-yellow display and with a resolution dot matrix 128x64 and an IC2 interface.
- The display includes the driver controller SSD1306 128 x 64 Segment Driver / OLED / PLED Common.

Metal casing with Internal magnet Characteristic: - Power 2-3W
- Impedance: 4 Ohm - Shape: Round - Thickness: 5.3mm / 0.21 " - Diameter: 40mm / 1.6" - Quantity: 1 unit

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 12V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)