Holder for HC-SR04 Ultrasonic Sensor Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. Code S0137 Available Price €0.99
0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display 0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display features: - Interface: I2C (logical level 3.3V) - Resolution: 128x64 - Angle of view:> 160 degrees - Screen color: blue and yellow (1/4 above yellow and 3/4 below blue) - Screen Dimension: 2.43cm / 0.96 " - IC Controller: SSD1306 - Power supply: 3.3V - 5VDC - Operating temperature: -20 ° C - 70 ° C - Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 " - Application: smart watch, MP3, thermometer, instruments, DIY projects, etc ... - It is an OLED screen module with blue-yellow display and with a resolution dot matrix 128x64 and an IC2 interface. - The display includes the driver controller SSD1306 128 x 64 Segment Driver / OLED / PLED Common. Code P0134 Available Regular price €7.50 -€1.00 Price €6.50
BMP280 Temperature Barometric Pressure Sensor Module/SPI This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features: - Interfaces: -I2C (up to 3.4 MHz) -SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range: - Temperature: -40ºC to + 85ºC0-100% - Pressure: 300-1100 hPa- Resolution of the measures: - Temperature: 0.01ºC Code M0134 Available Regular price €4.99 -€1.00 Price €3.99
40x Cables Female-Male 20cm 40x Cables Female-Male 20cm features: -Length: 20cm-Quantity: 40 cables-Connectors have male and female header contacts at either end-Compatible with female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0008 Available Price €2.49
PCB Heated Bed MK3 Alu 3mm 12V 24V 3D Printer PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer features: - Similar to MK2, can also be used with 12 volts or 24 volts - Measurements: 214 x 214 mm - 1 layer of 35μm (1 oz base) of copper Code I0091 Available Price €11.99
TTL Converter Module 5V - 3.3V Bidirectional I2C Logic Level Connecting a 3.3V device to a 5V system is a challenge.The bidirectional logic level converter is a small device that safely drops the signals from 5V to 3.3V and increases 3.3V to 5V at the same time.This level converter also works with 2.8V and 1.8V devices. What really separates this logic level converter from our previous versions is that it can successfully set its high and low voltages and go up and down between them safely on the same channel.Each level converter has the ability to convert 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two sources of voltage (high voltage and low voltage) that your system is using. Code M0153 Available Regular price €4.99 -€2.00 Price €2.99
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.99 -€0.20 Price €0.79
Lilypad Arduino compatible USB ATmega32u4 Board The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4.It has 9 digital input / output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery and a power button. restartIt contains everything necessary to support the microcontroller; simply connect it to a computer with a USB cable or a battery to start.The LilyPad Arduino USB differs from previous LilyPad cards in that the ATmega32U4 has built-in USB communication, eliminating the need for a separate USB to serial adapter. This allows the LilyPad Arduino USB to appear on a connected computer as a mouse and keyboard, as well as a virtual serial / COM (CDC) port. Code M0147 Available Regular price €7.99 -€1.00 Price €6.99
SIM800A GSM GPRS Shield Board Four Band GPRS Module with MCU Antenna The SIM800A modem is based on SIMCOM's dual band GSM / GPRS. Code W0104 Available Price €15.95
SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features: - GSM / GPRS SIM900 module-based development card / shield from Simcom - The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands). - The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board. - Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8 - GPRS mobile station class B - Complies with GSM phase 2/2 + - Class 4 (2 W @> Code W0090 Available Regular price €25.99 -€3.50 Price €22.49
A6 GSM GPRS Four Band GPRS Module with MCU Antenna GSM A6 Four Band GPRS Module with MCU Antenna features: - GSM / GPRS module / development board / shield based on GPRS A6 - Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission - Compact size and low current consumption - With energy saving technique, current consumption is as low as 5mA (sleep mode) - Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands - Working frequency: four-band network, 850 / 900/1800 / 1900MHz - Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module) - Working current: 2A maximum - Current Sleep: 5mA Code W0062 Available Price €14.49
SIM800L GPRS GSM SIM Board Quadband SIM800L GPRS GSM SIM Board Quadband features: Package includes: - SIM800L module, - 2x pin headers, - Spring antenna, - 3G PCB antenna - 15cm cable. - Supported SIM format: Micro SIM. Code W0017 Available Price €6.49
SIM800A GSM GPRS Shield Board Four Band GPRS Module with MCU Antenna The SIM800A modem is based on SIMCOM's dual band GSM / GPRS. Code W0104 Available Price €15.95
A6 GSM GPRS Four Band GPRS Module with MCU Antenna GSM A6 Four Band GPRS Module with MCU Antenna features: - GSM / GPRS module / development board / shield based on GPRS A6 - Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission - Compact size and low current consumption - With energy saving technique, current consumption is as low as 5mA (sleep mode) - Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands - Working frequency: four-band network, 850 / 900/1800 / 1900MHz - Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module) - Working current: 2A maximum - Current Sleep: 5mA Code W0062 Available Price €14.49
SIM800L GPRS GSM SIM Board Quadband SIM800L GPRS GSM SIM Board Quadband features: Package includes: - SIM800L module, - 2x pin headers, - Spring antenna, - 3G PCB antenna - 15cm cable. - Supported SIM format: Micro SIM. Code W0017 Available Price €6.49
SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features: - GSM / GPRS SIM900 module-based development card / shield from Simcom - The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands). - The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board. - Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8 - GPRS mobile station class B - Complies with GSM phase 2/2 + - Class 4 (2 W @> Code W0090 Available Regular price €25.99 -€3.50 Price €22.49