HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.48
Quartz Crystal Oscillator 16 MHz Quartz Crystal Oscillator 16 MHz features:- Low Profile Crystal Oscillator- Type: Quartz Crystal 16 MHz- Frequency: 16 MHz- Format: Low profile- Assembly: Intern Code E0012 Available Price €0.24
Flat female power supply socket, uninsulated 6.3 / 0.8 mm Uninsulated female flat faston power supply terminal 6.3 / 0.8 mm Code K0321 Available Price €0.08
10m Rigid cable, 22AWG red PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables -Rated voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0225 Backorder Price €3.21
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.09
LED Diode Assortment 5mm red, green, yellow pack 15 pcs LED Diode Assortment Kit 15 pcs 5mm red, green, yellow features:- Lens color: red, green, yellow - diffuse- Size: 5mm- Operating current: 20mA- Voltage (red) 1,8V-2,3V- Voltage (green) 3,2V-3,4V- Voltage (yellow) 1,8V-2,3V- Anode (A): Positive (long leg): 28mm- Catode (K): Negative (short leg): 25mm - Operating temperature: -25ºC/80ºC- Welding temperature: +260ºC - Quantity: 30 units*5x red*5x green*5x yellow Code P0160 Available Price €0.82
10x Female-Male Cables 20cm Jumpers Dupont 10x Female-Male Cables 20cm Jumpers Dupont features: -Length: 20cm-Quantity: 10 cables-Connectors have male and female header contacts at either end-Compatible with male and female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0009 Available Price €1.40
LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots features:- Supply voltage of the LED points: 1.8-2.4 VDC- LED color of the dots: red- Pin numbers: 16- Diameter of pins: 0.51mm- Step between pins: 2.54mm- Consumption current per segment: 30mA- Maximum admissible current per segment: 120mA- Power consumed per segment: 80mW- Segment numbers (points): 64- Diameter of a point: 3mm- Operating temperature: -35 ° C - + 85 ° C- Storage temperature: -35 ° C - + 85 ° C- Screen with common cathode connection for the rows and common anode for the columns- Screen size: 32x32x8 mm Code P0125 Available Regular price €2.39 -€1.00 Price €1.39
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €7.93
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.46
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €9.01
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €6.19
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.56
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Available Regular price €7.40 -€4.00 Price €3.40
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €9.50
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €20.58
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 ✗ Out-of-Stock Price €21.40
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €4.55
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €7.93
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.46
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €9.01
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €6.19
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.56
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Available Regular price €7.40 -€4.00 Price €3.40
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €9.50
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €20.58
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 ✗ Out-of-Stock Price €21.40
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €4.55