Gravity: Huskylens - An easy-to-use AI camera | vision sensor

Charger 2x18650 with EU Plug Cable features:
- This product is very convenient and easy to use
- Black
- Material: metal and plastic
- Weight: 74g
- Input voltage: AC 100 -240 V 50/60 Hz
- Compatible with: 18650 Li-ion
- When the 18650 battery is connected to the charger, the red LED light will be displayed, and means green in full charge status
- Output: DC 4.2 V, 1A
- Plug: EU plug
- Cable length: 38cm
- The battery are not included

Metal disc diameter 25mm with 4 mounting holes for 25T RC MG996R servos
25T metal disc for MG996R servomotors + 4 screws features:

- Material: Aluminum
- Gear teeth: 25T
- 4x M3 mounting holes rotated
- Diameter disc: 25mm
- Includes: 4 fixing screws.

WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins.

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

Maqueen Loader (ROB0156-L) includes a set of mechanical parts that can turn Maqueen into a loader. This kit contains all the spare parts, such as metal servo, mechanical parts, screws. Just a simple installation, then your Maqueen Car is ready to go! This play-and-learn kit comes with rich mechanical knowledge, which could allow students to benefit a lot from hands-on practices! Come and find more fun and interesting ways to play with Maqueen in this kit.

LED Diode Assortment Kit 50x Red Green Yellow Blue White features:
  
- Lens color: Red, green, yellow, blue - diffuse, light white
- Size: 5 mm
- Operating current: 20mA
- Voltage (red) 1.8V-2.3V
- Voltage (green) 3.2V-3.4V
- Voltage (yellow) 1.8V-2.3V
- Voltage (blue) 3.0V-3.2V
- Voltage (white) 3.2V - 3.4V
- Anode (A): Positive (long leg): 17mm
- Cathode (K): Negative (shorter leg): 15 mm
- Operating temperature: -25ºC / 80ºC
- Welding temperature: + 260ºC
- Quantity: - 50 units
                  - 10x red
                  - 10x green
                  - 10x yellow
                  - 10x blue
                  - 10x white

Maqueen Plus V2 is the latest version of the STEAM educational robot. Maqueen Plus  (DFRobot MBT0021-EN-18650) is optimised with more expansion ports, a higher capacity power supply and a larger body and is fully compatible with peripheral components. This makes it an accessible STEAM robot teaching tool for primary and secondary school students.

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level