CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.06
Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 Manufacturer: Taiwan Semiconductor 5x Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 features: - Type Output: fixed- Voltage Output: 3.3 V- Output Current: 800mA- Max input voltage: 12V- Operating temperature: -20C to + 85ºC- Encapsulated: SOT223- Dropout Voltage Vdo: 1.3V (1A)- Quantity: 5 units Code T0001 ✗ Out-of-Stock Price €0.62
40x Cables Female-Male 20cm 40x Cables Female-Male 20cm features: -Length: 20cm-Quantity: 40 cables-Connectors have male and female header contacts at either end-Compatible with female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0008 Available Price €2.06
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
Printed Circuit Board Terminal 3 poles 5.08mm pitch Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 3 poles 5.08mm pitch features: Number of Contacts: 3 Pitch: 5.08mm Number of Rows: 1 Mounting Type: PCB Gender: Male Allowable Section: 1.5mm2 (22- 14 AWG) Termination method: screw Type: screw terminal block Nominal current: 16A Nominal voltage: 250V Color: blue Material: Nylon 66 Depth: 10mm Width: 7.5mm Length: 10mm Code K0218 Available Price €0.28
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.12
DS1307 AT24C32 RTC real time module Can be used in projects of Arduino, PIC, AVR, STM32 and other. DS1307 AT24C32 RTC real time module features: - Based on DS1307Z- EEPROM memory 24C32 (4Kx8) available for the user- I2C interface- Hour, minutes, seconds, day, month, date, year- AM / PM time- Compensation of leap years- Quartz 32.768kHz- Dimensions: 28x26x8mm- Includes CR2032 3V battery Code M0101 Available Price €1.48
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 ✗ Out-of-Stock Price €21.40
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 ✗ Out-of-Stock Price €21.40
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €9.50
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Available Regular price €7.40 -€4.00 Price €3.40
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Regular price €7.40 -€2.00 Price €5.40
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €6.19
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.46
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €7.93
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.56
Gravity: Huskylens - An easy-to-use AI camera | vision sensor Huskylens is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0305) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF013 Available Price €59.08
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €9.91
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 ✗ Out-of-Stock Price €21.40
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €9.50
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Available Regular price €7.40 -€4.00 Price €3.40
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Regular price €7.40 -€2.00 Price €5.40
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €6.19
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.46
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €7.93
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.56
Gravity: Huskylens - An easy-to-use AI camera | vision sensor Huskylens is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0305) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF013 Available Price €59.08
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €9.91