M3 Hexagonal Spacer 25mm Male - Female Brass Characteristic: -Metric thread M3 -Male-Female separator 25mm -Quantity: 5 units Code H0048 Available Price €0.45
Current Sensor ACS712 AC/DC 20A Hall Current Ammeter Sensor used to measure the current in the circuit to which it is connected. It is based on the ACS712 chip, capable of measuring intensity in both DC and AC. Current Sensor ACS712 AC/DC 20A Hall Current Ammeter features: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 20A - Dimensions: 31 x 13 mm Code M0105 Available Price €3.38
Momentary Switch Push Button Red N/O 7mm Momentary Switch Push Button Red N/O 7mm features: - Momentary pushbutton N/O (normally open)- Red button- Dimensions approx. 7 mm x 27 mm- Recessed with nut and washer- Load current (supported): 1A to 230V / 2A to 125V- Drill to embed: 7 mm +/- 0.2- Operating temperature: -55º to +85ºC Code K0156 Available Price €0.45
Mini Speaker 40mm 2W Impedance 8 Ohm mp3 Metal casing with Internal magnet. Power 2W, Impedance: 8 Ohm, Shape: Round, Thickness: 5.3mm / 0.21 ", Diameter: 40mm / 1.6" Code M0215 Available Price €2.10
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
15x Electrolytic Capacitor 1uF 50V 105º C PIC for Arduino 15x Electrolytic Capacitor 1uF 50V 105º C PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 1uF-Maximum tension: 50V-Maximum temperature: 105º C-Dimensions: 5x11mm-Quantity: 15 units Code D0036 Available Price €0.09
Switch On/On 6-pin 6A SPDT This switch can be used for development projects and for the industry. All metal parts are not oxidized, the insulation material is of high quality.Its pins protected by an anti oxidant makes welding much easier. Switch On/On 6-pin 6A SPDT features: - Type: Latch SPDT- Material: Plastic, metal- Maximum operating current and voltage: 3A / 250V, 6A / 125V- Number of pins: 6- Pin size: 4.5x2 mm- Type of current: AC- Pins to be welded- Switch action: 2 positions On/On- Size: 13.2x12.7x33.3mm Code K0152 Available Price €0.48
Helping Magnifying Hand Tool It is a very ideal tool when the third hand is required.Helping Magnifying Hand Tool features:- Magnifying glass diameter 60mm- Weight: 0.5kg- Dimensions: approx. 15 (26) x 17 x 7cm Code H0011 Available Price €7.95
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €10.99
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €98.95
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Price €8.95
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Last items in stock Price €11.99
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 Backorder Price €10.99
LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader. The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features: - ATmega32u4 microcontroller, - Operating voltage 5V, - Power (recommended) 7-12V, - Digital pins I / O 20 (of which 7 can be used as PWM outputs), - Analog input pins 12, - DC current through I / O Pin 40 mA, - DC current for pin 3.3V 50 mA, - Flash memory 32 KB (of which 4 KB are used by the bootloader), - SRAM 2.5 KB, - EEPROM 1 KB, - Clock speed 16 MHz, - Interface: UART, USB, SPI, I2C, - USB communication - Atmega32u4, Code B0004 Available Price €10.90
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Backorder Price €45.90
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €10.99
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €98.95
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Price €8.95
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Last items in stock Price €11.99
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 Backorder Price €10.99
LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader. The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features: - ATmega32u4 microcontroller, - Operating voltage 5V, - Power (recommended) 7-12V, - Digital pins I / O 20 (of which 7 can be used as PWM outputs), - Analog input pins 12, - DC current through I / O Pin 40 mA, - DC current for pin 3.3V 50 mA, - Flash memory 32 KB (of which 4 KB are used by the bootloader), - SRAM 2.5 KB, - EEPROM 1 KB, - Clock speed 16 MHz, - Interface: UART, USB, SPI, I2C, - USB communication - Atmega32u4, Code B0004 Available Price €10.90
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Backorder Price €45.90