MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB

Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A.
Works with frequency signals up to 1.2 MHz.
Characteristic:
- Input voltage range: 2 - 5 VDC,
- Fixed output voltage: 5 VDC,
- Output accuracy: ± 0.1 V,
- Maximum output current: 2A,
- Ripple at full load: Vpp & lt; 70mV,
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 17x13mm.

Boost converter provides stable performance at 5V output even when operating with two AA batteries:
- With a 1.5V AA battery-output 5V / 200 ~ 300mA
- With two batteries 1.5V AA-output 5V / 500 ~ 600mA
It can be used for power applications and mobile devices to charge phones, cameras that use battery power.
DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module features:
- Input Voltage: 1.5V - 5.0V DC
- Output Voltage: 5V
- Max Output Current: 600mA
- LED operating indicator (input voltage min 2V)
- Protection over short circuit: no
- Measures of PCB 36 x 16

- The XL6009 module has a superior performance than the LM2577 module
- The regulator-booster of High performance
Characteristic:
- Based on the XL6009E1 regulator
- Input voltage: 3V-32V,
- Output voltage: 5-35V (adjustable),
- Output current: 2A maximum 3A (heat sink is required)
- Conversion efficiency: up to 94%
- Rectifier: not synchronous rectification
- Short circuit protection: current limitation, since recovery
- Operating temperature: industrial grade (-40 ° C - 85 ° C)
- Load regulation: ± 0.5%
- Voltage regulation: ± 0.5%
- Size: 50 x 22 x 15 mm

A high-performance step-up regulator
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features:

- Input voltage: 3.5 ~ 32v
- Output voltage: 4.5 ~ 35v (adjustable)
- Output current: 3A, maximum 5A (heatsink heat is required)
- Conversion efficiency: up to 90%
- Operating frequency: 100KHz
- Short circuit protection: current limiting
- Operating temperature: industrial grade (- 40 to 85)
- PCB dimensions: 52 x 37 mm

LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features:
- Step-up stepper adjustable module.
- Output voltage may be greater than the input
- Use a multimeter to check the output voltage and adjust the potentiometer
- Chip LM2577S-ADJ
- Input voltage: 3.5V -35V
- Output voltage: 4-35V
- Current output: 2A, max. 3A with heat sink
- Power max. 20W
- Operating temperature: -40 to + 85 ºC
- Conversion efficiency: up to 92%
- Size: 44 x 30 mm

A high-performance voltage regulator-riser 12V laptop power supply car accumulator
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:
- Input voltage: 10V-32V
- Output voltage: 12-35V (adjustable)
- Output current: 6A maximum
- Input current: 10A maximum
- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan
- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)
- Wiring: seamless terminal
- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)
- Current without load: 25 mA typical

Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A.
Works with frequency signals up to 1.2 MHz.
Characteristic:
- Input voltage range: 2 - 12 VDC,
- Fixed output voltage: 12 VDC,
- Output accuracy: ± 0.1 V,
- Maximum output current: 2A,
- Ripple at full load: Vpp & lt; 70mV,
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 17x13mm.

Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA.
Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off.
Works with frequency signals up to 1.5 MHz.
Characteristic:
- Input voltage range: 2.5 - 7 VDC,
- Fixed output voltage: 9 VDC,
- On / off mode pin EN: signal EN allowing this function to be performed,
- Output accuracy: ± 0.1 V,
- Output current: 150 - 400 mA,
- No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV,
- DC-DC conversion quality: 89%
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 19x15 mm.

DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA.

600W Boost Converter Booster Module DC voltage 12V to 80V features:
- Input voltage: 10V-60V
- Output voltage: 12-80V (adjustable)
- Output current: 10A
- Input current: 15A maximum
- Output power: 600W maximum
- Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%)
- Wiring: solderless terminal
- The minimum difference between the output and input voltage: 2V
- The ambient temperature exceeds 40 ° C, increase the dissipation of heat
- Short circuit protection: If between reverse polarity protection: None
- Size: 85 x 63 x 64 mm
- Weight 275g
Applications: