Protoboard Breadboard 5x7cm Protoboard Breadboard 5x7cm features: -PCB dimension: 5x7cm-Hole diameter: 1mm -Pitch: 2.54mm-Bakelite with copper fields Code PB021 Available Price €0.49
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0012 Available Price €1.15
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.12
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.64
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.09
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €7.84
Red Laser Module 650nm 5mW Head Point Adjustable Focal Length Red Laser Module 650nm 5mW Head Point Adjustable Focal Length features: - Type: red laser diode- Laser type: point- Adjustable Focus- Wavelength: 650nm- Output power: 5mW- Operating voltage: 4.5-5V- Operating intensity: <40mA- Operating temperature: -30ºC to 60ºC- Dimensions of the emitter: Φ12x35mm- Cable length: 130mm Code M0042 Available Regular price €2.88 -€0.50 Price €2.38
Banana Plug Cable Multimeter pack 5 colors Banana-banana plug cable for multimeter. Good quality tester cable. Code K0052 Available Price €4.12
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €5.78
600W Boost Converter Booster Module DC voltage 12V to 80V 600W Boost Converter Booster Module DC voltage 12V to 80V features: - Input voltage: 10V-60V - Output voltage: 12-80V (adjustable) - Output current: 10A - Input current: 15A maximum - Output power: 600W maximum - Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%) - Wiring: solderless terminal - The minimum difference between the output and input voltage: 2V - The ambient temperature exceeds 40 ° C, increase the dissipation of heat - Short circuit protection: If between reverse polarity protection: None - Size: 85 x 63 x 64 mm - Weight 275g Applications: Code A0009 Available Regular price €11.98 -€1.50 Price €10.48
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €1.82
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.14
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Available Price €3.21
DC Boost Step-Up Module 1.5-4.2V to 5V DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA. Code A0096 Available Price €1.89
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.22
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.12
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.40
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €4.54
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €5.78
600W Boost Converter Booster Module DC voltage 12V to 80V 600W Boost Converter Booster Module DC voltage 12V to 80V features: - Input voltage: 10V-60V - Output voltage: 12-80V (adjustable) - Output current: 10A - Input current: 15A maximum - Output power: 600W maximum - Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%) - Wiring: solderless terminal - The minimum difference between the output and input voltage: 2V - The ambient temperature exceeds 40 ° C, increase the dissipation of heat - Short circuit protection: If between reverse polarity protection: None - Size: 85 x 63 x 64 mm - Weight 275g Applications: Code A0009 Available Regular price €11.98 -€1.50 Price €10.48
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €1.82
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.14
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Available Price €3.21
DC Boost Step-Up Module 1.5-4.2V to 5V DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA. Code A0096 Available Price €1.89
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.22
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.12
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.40
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €4.54