Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €3.15 -€0.50 Price €2.65
LED Diode COB 20W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0032 Available Price €4.49
Cable Chain 10x10 1m for 3D CNC Printer Cable Chain 10x10 1m for 3D CNC Printer features: - Suitable for movements where cable displacement or twisting is needed, where cable protection is needed - Easy for installation And maintenance; Low noise, high speed wear resistant movement - The cable structure has been widely used in CNC machine tools, electronic equipment, fire fighting machinery and equipment, stone machinery, machinery glass, doors and windows of machines, injection molding machines, robots, overweight transport equipment, automated warehouses - Interior widths 10x10mm - Exterior measurement 15x20mm - Material: reinforced series polyamide - Length: 1m - Quantity: 1 unit Code I0138 Available Price €10.49
10.1 inch TFT LCD 1024x600 for Raspberry Pi controller kit HDMI TFT LCD screen for Raspberry Pi included in a complete package (adapters, stands, cables) for a compatible connection very easy with the Raspberry Pi. 10.1 inch (16:9) TFT LCD 1024x600 for Raspberry Pi controller kit features:Screen type: 1024 (R + G + B) * 600 dots LCD type: a-SI, Positive, Transmissive Display direction: 60 o'clock. Backlight: white LEDs. Interface: LVDS Operating temperature: -10ºC - + 60ºC. Active area: 222.72 x 125.28 mm. Code RA080 ✗ Out-of-Stock Price €78.99
12V 1.5W Do-it-yourself Mobile Solar Panel Photovoltaic Charger Cell Suitable for a small solar power system, etc. 12V 1.5W Do-it-yourself Mobile Solar Panel Photovoltaic Charger Cell features: - Working voltage: 12V - Output power: 1.5W - Product size: 115x 85x 3 mm Applications: - Charge cell phones - Home lighting - DIY solar powered toys Code A0070 Available Price €4.89
Cable 1x0.35 Flexible single-pole 0.35mm red 3m Characteristic: -Low-voltage electric cables -Standard: EN 50525-2-31 -Number of conductors: 1x0.35mm2 -Service voltage: 300 / 500V -Service temperature: at 70ºC -Resistance at 20ºC: 55.0 Ohm / Km -Weight (Kg / Km): 7 -Outer diameter: 2.4mm Code K0033 Backorder Price €0.45
Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - Quantity: 1 unit of 16 teeth GT2 pulley, 6mm wide and 2 studs - Ideal for fix on the axis of the motors of your 3D printer Code I0004 Backorder Regular price €1.94 -€0.50 Price €1.44
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.45
DC Boost Step-Up Module 1.5-4.2V to 5V DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA. Code A0096 Available Price €2.29
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €2.20
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.90
DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module Boost converter provides stable performance at 5V output even when operating with two AA batteries:- With a 1.5V AA battery-output 5V / 200 ~ 300mA- With two batteries 1.5V AA-output 5V / 500 ~ 600mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module features:- Input Voltage: 1.5V - 5.0V DC- Output Voltage: 5V- Max Output Current: 600mA- LED operating indicator (input voltage min 2V)- Protection over short circuit: no- Measures of PCB 36 x 16 Code A0001 Available Price €1.85
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.80
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Available Price €3.89
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.80
DC Boost Step-Up Module 1.5-4.2V to 5V DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA. Code A0096 Available Price €2.29
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.45
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €6.99
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Available Price €3.89
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.90
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €2.20
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module Boost converter provides stable performance at 5V output even when operating with two AA batteries:- With a 1.5V AA battery-output 5V / 200 ~ 300mA- With two batteries 1.5V AA-output 5V / 500 ~ 600mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module features:- Input Voltage: 1.5V - 5.0V DC- Output Voltage: 5V- Max Output Current: 600mA- LED operating indicator (input voltage min 2V)- Protection over short circuit: no- Measures of PCB 36 x 16 Code A0001 Available Price €1.85