Rechargeable Battery Samsung INR18650 2500mAh Li-ion Rechargeable Battery Samsung INR18650 2500mAh Li-ion 3.7V 20A unprotected features: IMPORTANT: This battery does not have a protection circuit. Use it at your own risk. Do not charge over 4.2V Do not discharge below 3V Do not change polarity Do not heat the battery, or expose it to high temperatures Do not wet or expose to environments of High humidity For long periods of storage it should be stored below 45 ° C After long periods of storage you will probably need to do some charging cycles to increase the capacity again. Quantity: 1 unit Nominal capacity: 2500mAh (0.2C, 2.75V discharge) Minimum capacity: 2450mAh (0.2C, 2.75V discharge) Charging voltage: 4.2 ± 0.05 V Code PP030 ✗ Out-of-Stock Price €5.44
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €1.89
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.12
JST PHR-2 Connector Male 2 PIN 2mm It is not possible to reverse the polarity by mistake. JST PHR-2 Connector Male 2 PIN 2mm features: Manufacturer JST Connector series: PH Connector: female connector Connector class: male Connector type: conduit-board Contactor raster: 2mm Number of pins: 2 Electrical mounting: THT Voltage Working: 100V Working current: 2A Working temperature: -25 ... 85 ° C Spatial orientation: vertical technical data sheet PH series Code K0211 Available Price €0.24
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.48
Anti-Static Tweezers ESD 117mm Anti-Static Tweezers ESD 117mm features: - Anti-static tweezers, curved tip, matt black- Length: 117mm- Width: 10mm- ESD pliers- High precision, without producing dust, resistant to high temperatures Code H0094 Available Price €1.48
USB Digital Power Voltmeter Tester Amps Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets ...USB Digital Power Voltmeter Tester Amps features:- Operating range: voltage 3.5 - 9V- Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%- Dimensions: 60 x 23 x 19mm Code K0083 Available Price €4.92
Connector BLS04 Female / Female 4 Pins RoHS Single Row Connector BLS04 Female / Female 4 Pins RoHS Single Row features: - Step between pins: 2.54 mm- Manufacturer: Maritex- Number of connections: 4 in a single row- Type: Female / Female- RoHS standard Code K0120 Available Price €0.09
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.40
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.14
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.22
600W Boost Converter Booster Module DC voltage 12V to 80V 600W Boost Converter Booster Module DC voltage 12V to 80V features: - Input voltage: 10V-60V - Output voltage: 12-80V (adjustable) - Output current: 10A - Input current: 15A maximum - Output power: 600W maximum - Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%) - Wiring: solderless terminal - The minimum difference between the output and input voltage: 2V - The ambient temperature exceeds 40 ° C, increase the dissipation of heat - Short circuit protection: If between reverse polarity protection: None - Size: 85 x 63 x 64 mm - Weight 275g Applications: Code A0009 Available Regular price €11.98 -€1.50 Price €10.48
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.12
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €4.54
DC Boost Step-Up Module 1.5-4.2V to 5V DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA. Code A0096 Available Price €1.89
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.02
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Available Price €3.21
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €1.82
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.40
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.14
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.22
600W Boost Converter Booster Module DC voltage 12V to 80V 600W Boost Converter Booster Module DC voltage 12V to 80V features: - Input voltage: 10V-60V - Output voltage: 12-80V (adjustable) - Output current: 10A - Input current: 15A maximum - Output power: 600W maximum - Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%) - Wiring: solderless terminal - The minimum difference between the output and input voltage: 2V - The ambient temperature exceeds 40 ° C, increase the dissipation of heat - Short circuit protection: If between reverse polarity protection: None - Size: 85 x 63 x 64 mm - Weight 275g Applications: Code A0009 Available Regular price €11.98 -€1.50 Price €10.48
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.12
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €4.54
DC Boost Step-Up Module 1.5-4.2V to 5V DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA. Code A0096 Available Price €1.89
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.02
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Available Price €3.21
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €1.82