Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Regular price €8.22 -15% Price €6.99
Resistor 470R Ohm 5% 0,25W 1/4W Resistors 470R Ohm 5% 0,25W 1/4W features:- 470R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0010 Available Price €0.07
Transistor heat sink with TO-220/TIP120 box Heat sink for transistors with TO-220 / TIP120 box Transistor heat sink with TO-220/TIP120 box features: Aluminum heatsink: - Dimensions: 25x15x10mm Code T0069 Available Price €0.37
Solder Wire Tin Sn60Pb40 Lead 2.5% Flux 1.5mm 100g Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.5mm features: - 100gr. 1.5mm diameter welding wire. 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit Code Q0105 ✗ Out-of-Stock Price €7.40
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €7.85
USB Digital Power Voltmeter Tester Amps Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets ...USB Digital Power Voltmeter Tester Amps features:- Operating range: voltage 3.5 - 9V- Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%- Dimensions: 60 x 23 x 19mm Code K0083 Available Price €4.92
Rechargeable Battery Samsung ICR18650 2600mAh Li-ion Characteristic: - Lithium Battery WITHOUT Protection - Nominal capacity: 2600mAh (discharge of 0.2C, 2.75V) - Minimum capacity: 2550mAh (0.2C, 2.75V discharge) - Charging voltage: 4.2 ± 0.05 V - Nominal voltage: 3.63V - Charging method: DC-CV (constant voltage with current limited) - Charging current: standard charge: 1300mA, fast charge: 2600mA - Charging time: standard charge: 3 hours, fast charge: 2.5 hours - Max. Charging current: 2600mA (ambient temperature 25 °) - Max. Discharge current: 5200mA (ambient temperature 25 °) - Discharge cut-off voltage: 2.75V - Cell weight: 47.0g maximum - Cell dimension: Height: 65.00 mm max., Diameter: 18.40 mm max. Code PP018 ✗ Out-of-Stock Price €4.95
Sensor SCT-013-030, Non-Invasive 30A AC Current Meter The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-030, Non-Invasive 30A AC Current Meter features: Input current: 0 to 30A AC Output voltage: 0 to 1 V AC Built-in load resistance: 62 Ω Winding ratio: 1800: 1 Operating temperature range: -25 ° C to 70 ° C Cable length: 1 m Sensor weight: approximately 45 g Sensor SCT013-030 datasheet Code M0203 Available Price €5.36
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
Joystick Shield compatible with Arduino UNO Mega Shield allows you to be directly punched to an Arduino Uno, Mega board and convert your Arduino board into a controller like the game console system. Joystick Shield compatible with Arduino UNO Mega features: - 3.3V / 5V voltage- 4 large buttons ABCD- 2 small EF buttons- 1 button on the joystick)- 2-axis joystick (x, y)- Nokia 5110 LCD screen interface- Interface nRF24L01 +- Dimensions of PCB: 87 x54 mm Code M0021 Available Price €4.09
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €5.36
MyoWare Muscle Sensor Development Kit - OBSOLETE This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together. Code SP074
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 ✗ Out-of-Stock Price €16.12
Screw Shield V2 for Arduino UNO Screw Shield V2- Arduino ScrewShield UNO features: Screw Shield V2 allows: - Being punctured directly to an Arduino Uno- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0172 Available Regular price €4.09 -€1.00 Price €3.09
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €6.53
Arduino NICLA Voice Nicla Voice combines a powerful Syntiant® NDP120 Neural Decision Processor™ (NDP), a high-performance IM69D130 microphone, a BMI270 6-axis intelligent motion sensor, a BMM150 3-axis magnetometer and Bluetooth® Low Energy connectivity. Code ABX00061 Last items in stock Price €79.00
Qwiic cable protoboard - 4 pin This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme: Code SP020 Available Price €1.64
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
Joystick Shield compatible with Arduino UNO Mega Shield allows you to be directly punched to an Arduino Uno, Mega board and convert your Arduino board into a controller like the game console system. Joystick Shield compatible with Arduino UNO Mega features: - 3.3V / 5V voltage- 4 large buttons ABCD- 2 small EF buttons- 1 button on the joystick)- 2-axis joystick (x, y)- Nokia 5110 LCD screen interface- Interface nRF24L01 +- Dimensions of PCB: 87 x54 mm Code M0021 Available Price €4.09
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €5.36
MyoWare Muscle Sensor Development Kit - OBSOLETE This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together. Code SP074
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 ✗ Out-of-Stock Price €16.12
Screw Shield V2 for Arduino UNO Screw Shield V2- Arduino ScrewShield UNO features: Screw Shield V2 allows: - Being punctured directly to an Arduino Uno- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0172 Available Regular price €4.09 -€1.00 Price €3.09
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €6.53
Arduino NICLA Voice Nicla Voice combines a powerful Syntiant® NDP120 Neural Decision Processor™ (NDP), a high-performance IM69D130 microphone, a BMI270 6-axis intelligent motion sensor, a BMM150 3-axis magnetometer and Bluetooth® Low Energy connectivity. Code ABX00061 Last items in stock Price €79.00
Qwiic cable protoboard - 4 pin This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme: Code SP020 Available Price €1.64