Quartz Crystal Oscillator 16 MHz

Red Laser Cross Module 650nm 5mW Head Point Adjustable Focal Length features:
- Type: red laser diode
- Type of laser: cross
- Adjustable Focus
- Wavelength: 650nm
- Output power: 5mW
- Operating voltage: 4.5-5V
- Operating intensity: <40mA
- Operating temperature: -30ºC to 60ºC
- Dimensions of the emitter: Φ12x35mm
- Cable length: 130mm

5x Push Switch Button B3F Omron Red Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1
- LED status indicators - Transmission speed: 5kB / s
- Fuse protector against possible damage to the USB port
- Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux
- Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦
- Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦
- CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦
- AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦

Resistor 200R Ohm 5% 0,25W 1/4W features:
-200R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython.

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A.
The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features:
- Input voltage: 230VAC
- Output voltage: 0-30V adjustable
- Output current: 0-5A adjustable
- Backlit display
- Protection against over-consumption and short circuit
- Cooled by fan
- Includes crocodile clip cables Uni-T UTP3315TFL datasheet
Load Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.2% + 3mA
Line Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.1% + 5mA
Ripple and Noise
Voltage 1mV rms
Current 3mA rms