Resistor 330 Ohm 5% 0,25W 1/4W Resistor 330 Ohm 5% 0,25W 1/4W features:-330 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0009 Available Price €0.08
Shield Sensor Expansion Board Arduino compatible V2.0 Arduino Shield Sensor Expansion Board V2.0 features: The Mega Sensor Shield V2.0 allows: - To be directly punched to an Arduino Uno, Mega, Leonardo board - Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more - Size: 100x54x12 mm Code M0129 Available Price €3.89
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Last items in stock Price €6.49
Battery LIPO 180mAh 3.7V LITHIUM POLYMER BATTERY Battery LIPO 180mAh 3.7V features: -Battery type-lithium polymer. -Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 180 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit Dimensions: -Length / depth of the battery- 20 mm -Battery width / diameter -31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Wires: Red: positive. Black: negative. Yellow: thermistor output. The technical file: Battery LIPO.pdf Code PP038 Backorder Price €3.49
Universal Battery Tester AA AAA 1.5V 9V Universal Battery Tester AA AAA 1.5V 9V features: - Type: Household battery tester- You accept:* Button batteries* 1.5 V: AAA, HP16, MN2400, AA R03, HP7, MN1500, UM3 C, HP11, MN1400, SP11, LR14, UM2 D, HP2, MN1300, SP2, R20* 9 V: PP3, 6F22, MN1604, 006P* Dimensions: 5.5 x 5.2 cm Code M0064 Available Price €2.99
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.95
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
Module MAX3232 Converter RS232 to TTL Port DB9 female This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features: - Input voltage: 3.3 - 5 VDC- Multi-channel RS232 controller / receiver MAX3232- Transmission / reception speed up to 250 kbit / s- DB9 serial port- Interface with four pins: - TX: transmission signal - RX: reception signal - VCC: Supply voltage - GND: connects the power cathode- Operating temperature: -65 ° C - + 150 ° C- UART communication- Includes a 4-wire female / female connector for easy connection with the arduino Code C0016 Available Price €2.90
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.90
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €6.99
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Backorder Price €3.89
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module Boost converter provides stable performance at 5V output even when operating with two AA batteries:- With a 1.5V AA battery-output 5V / 200 ~ 300mA- With two batteries 1.5V AA-output 5V / 500 ~ 600mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module features:- Input Voltage: 1.5V - 5.0V DC- Output Voltage: 5V- Max Output Current: 600mA- LED operating indicator (input voltage min 2V)- Protection over short circuit: no- Measures of PCB 36 x 16 Code A0001 Available Price €1.85
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
600W Boost Converter Booster Module DC voltage 12V to 80V 600W Boost Converter Booster Module DC voltage 12V to 80V features: - Input voltage: 10V-60V - Output voltage: 12-80V (adjustable) - Output current: 10A - Input current: 15A maximum - Output power: 600W maximum - Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%) - Wiring: solderless terminal - The minimum difference between the output and input voltage: 2V - The ambient temperature exceeds 40 ° C, increase the dissipation of heat - Short circuit protection: If between reverse polarity protection: None - Size: 85 x 63 x 64 mm - Weight 275g Applications: Code A0009 Last items in stock Price €14.49
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.80
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €2.20
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.90
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €6.99
LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up LM2577S 3A DC Boost Step-Up Controller Adjustable Step-Up features: - Step-up stepper adjustable module. - Output voltage may be greater than the input - Use a multimeter to check the output voltage and adjust the potentiometer - Chip LM2577S-ADJ - Input voltage: 3.5V -35V - Output voltage: 4-35V - Current output: 2A, max. 3A with heat sink - Power max. 20W - Operating temperature: -40 to + 85 ºC - Conversion efficiency: up to 92% - Size: 44 x 30 mm Code A0066 Backorder Price €3.89
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module Boost converter provides stable performance at 5V output even when operating with two AA batteries:- With a 1.5V AA battery-output 5V / 200 ~ 300mA- With two batteries 1.5V AA-output 5V / 500 ~ 600mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.DC-DC Boost Module 0.9~5V 600mA Converter Step Up Module features:- Input Voltage: 1.5V - 5.0V DC- Output Voltage: 5V- Max Output Current: 600mA- LED operating indicator (input voltage min 2V)- Protection over short circuit: no- Measures of PCB 36 x 16 Code A0001 Available Price €1.85
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
600W Boost Converter Booster Module DC voltage 12V to 80V 600W Boost Converter Booster Module DC voltage 12V to 80V features: - Input voltage: 10V-60V - Output voltage: 12-80V (adjustable) - Output current: 10A - Input current: 15A maximum - Output power: 600W maximum - Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%) - Wiring: solderless terminal - The minimum difference between the output and input voltage: 2V - The ambient temperature exceeds 40 ° C, increase the dissipation of heat - Short circuit protection: If between reverse polarity protection: None - Size: 85 x 63 x 64 mm - Weight 275g Applications: Code A0009 Last items in stock Price €14.49
9V power module with 400mA step up output On/Off DM06 Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA. Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off. Works with frequency signals up to 1.5 MHz. Characteristic: - Input voltage range: 2.5 - 7 VDC, - Fixed output voltage: 9 VDC, - On / off mode pin EN: signal EN allowing this function to be performed, - Output accuracy: ± 0.1 V, - Output current: 150 - 400 mA, - No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV, - DC-DC conversion quality: 89% - Operating temperatures: -40ºC - + 85ºC, - PCB size: 19x15 mm. Code A0094 Available Price €3.80
Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB Boost converter provides stable performance at 5V output even when operating with two AA batteries:- Input voltage min 2V-output 5V/ ~ 400mA- Input voltage min 3V-output 5V/ ~ 800mA- Input voltage min 3.5V-output 5V/ ~ 1200mAIt can be used for power applications and mobile devices to charge phones, cameras that use battery power.Boost Converter DC-DC 2V-5V to 5V 1200mA Power Charger USB features:- Input Voltage: 2V - 5.0V DC- Output Voltage: 5.1V + / 0.1V- Max Output Current: 1200mA- LED operation indicator- Protection over short circuit: no- Measures of PCB 26 x 18 Code A0002 Available Price €2.20