Potentiometer B5K Linear 5K OHM kΩ

The 28BYJ-48 has everything you need to start using stepper motors in your project. A stepper motor converts digital impulses into small movement steps. in one direction Characteristic: - Motor model: 28BYJ-48
- Motor phases: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per lap: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm
- Operating temperature: -45ºC to + 125ºC
- Motor cable length: 19cm
- Motor block diameter: 28mm
- Motor dimensions: 42mm x 32mm x 30mm

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 5.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

M18 Inductive Proximity Sensor features:
- Inductive proximity sensor detection switch LJ18A3-8-Z / BX
- NPN DC6-36V
- A Often used for 3D printer bed leveling
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open )
- Detecting distance 8mm
- DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition)
- Head diameter 18 mm
- Size 6.9 x 2cm
- Cable length 90cm

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Mega2560 V3.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Mega2560, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.