SD Card Module Reader

The 2.5mm female jack connector is a connector to provide power to computers, LED TVs, routers, etc ...
This 2.5mm female jack connector adapter soldered on a PCB board, is ideal for use in our projects.
It has connection points where we can easily solder some pins to connect it directly to a breadboard, or solder a cable over those same connection points.
Adapter 2.5mm female power jack with PCB features:
- Connector type: 2.5mm female jack ,
- Color: black,
- Nominal voltage: 12v DC,
- Maximum current: 0.5A DC,
- Insulation resistance: ‰ ¥ 100MΩ,
- Operating temperature: -25ºC to + 85ºC,
- Number of output pins: 3
- Pitch between output pins: 2.54mm.

This module is a timed switch that allows you to program several types of applications such as lights. Time Switch Module 12V NE555 Monostable Switch Delayed features:

TPA3118 1X60W PBTL Channel Only Amplifier features:
- Chip: TPA3118
- Power supply: DC 8V ~ 24V
- Channel type: Single channel
- Output power: 1 x 60 W.
- Matching output: 4 ~ 8 Ohm
- Mono PBTL mode
- Size (LxWxH): 46 x 35 x 13 mm

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

Characteristic: - Operating voltage: 3-6V
- Max flow: 80-120 l / h
- Maximum pumping height: 40-110cm
- Continuous working time of 500 hours
- Cable length: 20cm
- Inside outlet diameter: 5 mm
- Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART).

M12 High Resolution Lens, 12MP, 160° FOV, 3.2mm Focal length, Compatible with Raspberry Pi High Quality Camera M12

Buzzer 5V Passive 5 to 12V DC features:
- Input voltage: 4V to 12V
- Diameter: 17mm
- Height: 7mm
- f = 4kHz +/- 500
- Pin Separation: 10mm
- Maximum Current:

Blue LED.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: blue
- Size: 5.5x12.5 mm
- 1 LED included