DS18B20 Temperature Sensor 0.5ºC TO-92 Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:- Device function: Temperature sensor- Type of output: Digital- Supply voltage: 3V to 5.5V- Accuracy: ± 0.5ºC- Temperature threshold: Programmable- Operating temperature: -55ºC to + 125ºC- Encapsulated: TO-92- Supply current: 1.5mA Code S0014 Available Price €1.61
BME280 Digital Temperature Humidity Barometric Pressure Module This module includes the component BME280 that is translated into a digital signal.The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features: - Interfaces:- I2C (up to 3.4 MHz)- SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range:- Temperature: -40ºC to + 85ºC- Humidity: 0-100%- Pressure: 300-1100 hPa- Resolution of the measures:- Temperature: 0.01ºC- Humidity: 0.008%- Pressure: 0. 18Pa- Accuracy of the measures:- Temperature: +/> Code M0135 ✗ Out-of-Stock Regular price €9.88 -€5.00 Price €4.88
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.57
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €1.78
BBC micro:bit V2.21 Go - Starter Pack The novelty of micro:Bit for a more lively introduction to technology for children. The micro:bit is a pocket computer that can be encoded, customized and controlled for the implementation of digital ideas and games. It measures just 4x5cm and features a fun and easy to use design, so users can create anything from games and animations to slick stories at school, at home or anywhere - all it takes is imagination and creativity. It is fully programmable. This means that each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer, Bluetooth 5.0 technology, microphone and speaker. It contains a quick start guide in the same package. Code B0125 Available Regular price €19.79 -€0.96 Price €18.83
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
L7805 Voltage Regulator 5V 1.5A TO-220 L7805CV Voltage Regulator 5V 1.5A TO-220 features:-Type Output: Fixed-Voltage Output: 5V-Manufacturer: ST Microelectronics-Output current: 1.5A-Max input voltage: 35V-Input input min.: 5V-Operational temperature: 0ºC to + 125ºC-Encapsulated: TO-220-Polarity: Positive Code T0022 Available Price €0.32
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €9.91
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth, 4MB ESP32-WROOM-32E (ESP32-DEVKITC-32E) is an evaluation board with ESP32 processor, 4MB FLASH, 802.11 a/b/g/n (Wi-Fi, WiFi, WLAN) and BlueTooth® Smart Ready 4.x dual-mode. It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use. Code W0125 ✗ Out-of-Stock Price €11.53
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 ✗ Out-of-Stock Price €9.01
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €3.93 -€1.00 Price €2.93
Wifi module adapter ESP12 ESP12E The adaptor for the well-known ESP-12 and ESP-12E module Code W0025 Available Price €0.74
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 ✗ Out-of-Stock Price €7.43
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €7.84
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €5.36 -€1.29 Price €4.07
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth, 4MB ESP32-WROOM-32E (ESP32-DEVKITC-32E) is an evaluation board with ESP32 processor, 4MB FLASH, 802.11 a/b/g/n (Wi-Fi, WiFi, WLAN) and BlueTooth® Smart Ready 4.x dual-mode. It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use. Code W0125 ✗ Out-of-Stock Price €11.53
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 ✗ Out-of-Stock Price €9.01
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €3.93 -€1.00 Price €2.93
Wifi module adapter ESP12 ESP12E The adaptor for the well-known ESP-12 and ESP-12E module Code W0025 Available Price €0.74
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 ✗ Out-of-Stock Price €7.43
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €7.84
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €5.36 -€1.29 Price €4.07