Power Supply Transformer 220V AC/DC 2A 12V Power Supply Transformer 220V AC/DC 2A 12V features:- Input voltage: 100~240V 50Hz- Output voltage: DC 12V- Output current: 2A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0015 Available Price €3.96
TIP120 Low voltage Darlington transistor NPN 60V 5A with collector-emitter saturation pack 5ps TIP120 Low voltage Darlington transistor NPN 60V 5A with collector-emitter saturation pack 5ps features: - Package / Case: TIP120 TO-220- Manufacturer: ST Microelectronics- VCBO collector-base voltage: 60V- VCEO collector-emitter voltage: 60V- VEBO emitter-base voltage: 5V- Collector continuous current: 5A- DC MAX collector current: 8A- Maximum power dissipation: 65W if T <= 25ºC- Storage temperature: -65ºC to + 150ºC- Maximum operating junction temperature: + 150ºC Code T0070 Available Price €0.99
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €1.78
PAM8403 2x3W Digital Amplifier Channel Stereo PAM8403 2x3W Digital Amplifier Channel Stereo features: - Up to 3W in each channel- Chip: PAM8403- Power supply: 5V- Power: 2 outputs of 3 watts each- Measures: 21x18 mm- Suitable impedance speakers: 4 Ohm Code M0027 Available Price €1.56
PCB Circuit Board Marker Pen 0.4mm for printed circuits PCB Circuit Board Marker Pen 0.4mm for printed circuits features: - Permanent resistance ink to acid attack- Resistant to sunlight- Ideal to write on almost any flat surface, such as PCBs, glass, plastic, metal, etc.- Quantity: 0.4mm- 1 unit Code V0004 Available Price €1.73
Thermal tape 20mm type Kapton Characteristic: - Supports up to 280ºC - Electrical and antistatic insulation - Resistant to acidic products and alkaline - Solvent resistant - Adhesive - Length Approx: 26m Code I0053 Available Regular price €4.01 -€1.36 Price €2.65
Wire stripping pliers The pliers enable precise cutting and stripping of single and multi-core cables with diameters between 0.8 and 2.6 mm / 110-20 AWG. Code H0579 Available Price €3.30
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €24.37
HX711 Modulo Conversor + Celda de Carga 1kg Load Cell Conversor A/D 24bits M0119 The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0119 Available Regular price €4.78 -€0.79 Price €3.99
Digital Touch Sensor B21 The module is based on a touch sensitive IC capacitive touch switch module (TTP223B). In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features: - Low power consumption - Input voltage: 2 - 5.5VDC - Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation - 3-pin control interface: 1- GND 2- VCC 3- Control signal (output pin) - Power indicators: Bright green LED when the sensor is on Code M0130 Available Price €1.23
Circular force sensing resistor The resistance of the sensor has a force measurement range of 0-10 kgIts resistance varies depending on how much pressure is applied to the detection area, the greater the force, the lower the resistance.Peel and stick the rubber backing on the other side of the detection area to mount.It can detect the applied force in the detection area in the range of 0g-10kg. Circular force sensing resistor features: - Detection area: 1.27cm / 0.5 inches- Output signal: passive variable resistance- Force detection range: 0 g ~ 10 kg- Length: 6 cm / 2.36 inches- Width: 1.9cm / 0.75 inches Code S0135 Available Price €7.02
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Available Regular price €2.64 -€1.00 Price €1.64
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.47 -€0.99 Price €1.48
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €5.19 -€1.20 Price €3.99
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Available Regular price €2.47 -€0.99 Price €1.48
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Available Regular price €4.78 -€0.79 Price €3.99
Ceramic Piezoelectric Disc 35mm with Mika PVC 49mm Characteristic: - Diameter: 35mm - Frequency: 2.3 kHz - Impedance (resonance): 300 Ohm - Capacity (at 1kHz): 25,000 pF - Dimensions: 35x0.50mm Code M0167 Available Price €0.40
Piezoelectric Vibration Sensor for Arduino UNO When the piezoelectric ceramic shock will generate an electrical signal, the analog port of the Arduino controller may perceive weak vibration signals. Can also be done with jobs related to vibration interactions, such as electronic drums. Code M0168 Available Price €2.06
HX711 Modulo Conversor + Celda de Carga 1kg Load Cell Conversor A/D 24bits M0119 The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0119 Available Regular price €4.78 -€0.79 Price €3.99
Digital Touch Sensor B21 The module is based on a touch sensitive IC capacitive touch switch module (TTP223B). In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features: - Low power consumption - Input voltage: 2 - 5.5VDC - Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation - 3-pin control interface: 1- GND 2- VCC 3- Control signal (output pin) - Power indicators: Bright green LED when the sensor is on Code M0130 Available Price €1.23
Circular force sensing resistor The resistance of the sensor has a force measurement range of 0-10 kgIts resistance varies depending on how much pressure is applied to the detection area, the greater the force, the lower the resistance.Peel and stick the rubber backing on the other side of the detection area to mount.It can detect the applied force in the detection area in the range of 0g-10kg. Circular force sensing resistor features: - Detection area: 1.27cm / 0.5 inches- Output signal: passive variable resistance- Force detection range: 0 g ~ 10 kg- Length: 6 cm / 2.36 inches- Width: 1.9cm / 0.75 inches Code S0135 Available Price €7.02
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Available Regular price €2.64 -€1.00 Price €1.64
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.47 -€0.99 Price €1.48
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €5.19 -€1.20 Price €3.99
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Available Regular price €2.47 -€0.99 Price €1.48
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Available Regular price €4.78 -€0.79 Price €3.99
Ceramic Piezoelectric Disc 35mm with Mika PVC 49mm Characteristic: - Diameter: 35mm - Frequency: 2.3 kHz - Impedance (resonance): 300 Ohm - Capacity (at 1kHz): 25,000 pF - Dimensions: 35x0.50mm Code M0167 Available Price €0.40
Piezoelectric Vibration Sensor for Arduino UNO When the piezoelectric ceramic shock will generate an electrical signal, the analog port of the Arduino controller may perceive weak vibration signals. Can also be done with jobs related to vibration interactions, such as electronic drums. Code M0168 Available Price €2.06