Kapton type 10mm thermal tape Characteristic: - Supports up to 280ºC - Electrical and antistatic insulation - Resistant to acid and alkaline products - Resistant to solvent - Adhesive - Length Approx: 33m - Polyamide adhesive tape 10mm - Known as Kapton polyamide tape - Product for welding works on those that need to protect some component from the heat Code I0061 Available Price €1.78
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €24.75 -€6.00 Price €18.75
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-1 unit - 10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0082 Available Price €0.07
10x Push button 6x6x9mm 10x Push button 6x6x9mm features: -Touch Push Tact Switch mini electronic Arduino push button -Measures: 6x6x9mm -Quantity: 10 units Code K0077 Available Price €0.16
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.44
Velostat/Linqstat film 30x30cm for projects - Adafruit Velostat or Linqstat film of pressure sensitive material ideal for DIY projects on Arduino, Raspberry or other platforms. When folded or creased it reduces its resistance allowing for flexible sensors. Code RA123 Available Price €5.37
LED Diode Assortment Kit 30 pcs 5mm red, green, yellow LED Diode Assortment Kit 30 pcs 5mm red, green, yellow features:- Lens color: red, green, yellow - diffuse- Size: 5mm- Operating current: 20mA- Voltage (red) 1,8V-2,3V- Voltage (green) 3,2V-3,4V- Voltage (yellow) 1,8V-2,3V- Anode (A): Positive (long leg): 28mm- Catode (K): Negative (short leg): 25mm - Operating temperature: -25ºC/80ºC- Welding temperature: +260ºC - Quantity: 30 units*10x red*10x green*10x yellow Code P0011 Available Price €0.05
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.39
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Last items in stock Regular price €2.64 -€1.00 Price €1.64
HX711 Modulo Conversor + Celda de Carga 1kg Load Cell Conversor A/D 24bits M0119 The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0119 Available Regular price €4.78 -€0.79 Price €3.99
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €5.19 -€1.20 Price €3.99
Load cell 10kg Load cell Load Cell Weight Sensor 10kg features: Load range: 10kg Operating voltage: 3VDC ~ 14 VDC. Rated output: 1.0 ± 0.15mV/V. Repeatability: 0.03% FS Effect of temperature on output: 0.01% F.S / ° C Temperature effect on zero: 0.05% F.S / ° C Code M0127 Available Regular price €2.88 -€1.00 Price €1.88
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.31 -€0.39 Price €1.92
Piezoelectric Vibration Sensor for Arduino UNO When the piezoelectric ceramic shock will generate an electrical signal, the analog port of the Arduino controller may perceive weak vibration signals. Can also be done with jobs related to vibration interactions, such as electronic drums. Code M0168 Available Price €2.06
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Available Regular price €2.47 -€0.99 Price €1.48
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.47 -€0.99 Price €1.48
Load Cell Weight Sensor 50kg Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV. Code Sp096 Last items in stock Regular price €6.36 -€0.99 Price €5.37
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Available Regular price €4.78 -€0.79 Price €3.99
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Last items in stock Regular price €2.64 -€1.00 Price €1.64
HX711 Modulo Conversor + Celda de Carga 1kg Load Cell Conversor A/D 24bits M0119 The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0119 Available Regular price €4.78 -€0.79 Price €3.99
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €5.19 -€1.20 Price €3.99
Load cell 10kg Load cell Load Cell Weight Sensor 10kg features: Load range: 10kg Operating voltage: 3VDC ~ 14 VDC. Rated output: 1.0 ± 0.15mV/V. Repeatability: 0.03% FS Effect of temperature on output: 0.01% F.S / ° C Temperature effect on zero: 0.05% F.S / ° C Code M0127 Available Regular price €2.88 -€1.00 Price €1.88
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.31 -€0.39 Price €1.92
Piezoelectric Vibration Sensor for Arduino UNO When the piezoelectric ceramic shock will generate an electrical signal, the analog port of the Arduino controller may perceive weak vibration signals. Can also be done with jobs related to vibration interactions, such as electronic drums. Code M0168 Available Price €2.06
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Available Regular price €2.47 -€0.99 Price €1.48
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.47 -€0.99 Price €1.48
Load Cell Weight Sensor 50kg Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV. Code Sp096 Last items in stock Regular price €6.36 -€0.99 Price €5.37
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Available Regular price €4.78 -€0.79 Price €3.99