Resistor 4.7R Ohm 5% 0,125W 1/8W Resistor 4.7R Ohm 5% 0,125W 1/8W features:-4.7R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.125W-Dimensions: 1.85x3.5mm Code D0001 Available Price €0.07
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.31
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €2.88
20x Ceramic Capacitor 470pF 50v 2,54 PCB PIC for Arduino 20x Ceramic Capacitor 470pF 50v 2,54 PCB PIC Arduino features:-Type: ceramic NPO-Tolerance: +/-5%-Dimensions: diameter 5mm, pitch 2.54mm Code D0067 Available Price €0.04
Double Side Prototype PCB Board 5x7cm Double Side Prototype PCB Board 5x7cm features: -Thickness of PCB: 1.6mm-Material: high quality FR-4 glass fiber PCB-Presented and numbered on both sides-Top and bottom are identical copper layers-Pads grid (pitch) 2.54mm/0.1", hole diameter 0.9mm Code PB019 Available Price €0.82
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Last items in stock Price €2.44
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.82
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 ✗ Out-of-Stock Price €1.78
PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features: - Compatible controller PL2303HXA- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)- 2.5A self-recovery protective fuse- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error. Code C0002 Available Price €2.31
RS232/485/422 to RJ45 Ethernet Module, TCP/IP to serial, POE Function Converter RS232/485/422 to Ethernet RJ45 has been designed for the industrial environment. It combines multiple functions including serial server, Modbus gateway, MQTT gateway, RS485 to JSON, etc. The module has an RS232/485/422 and Ethernet port (PoE function).Suitable for applications such as data acquisition, IoT gateway, IoT security. and smart device monitoring. Code WV015 ✗ Out-of-Stock Price €32.64
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €4.29
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €5.45
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.26
SparkFun FTDI Basic Breakout - 3.3V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP024 Available Price €16.52
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.06
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
6-pin/10-pin Kanda DIL adapter 6-pin/10-pin Kanda DIL adapter features: - Connector for Usbasp Programmer AVR Atmega8 Atmega128 Code B0051 Available Price €1.07
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.39
PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features: - Compatible controller PL2303HXA- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)- 2.5A self-recovery protective fuse- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error. Code C0002 Available Price €2.31
RS232/485/422 to RJ45 Ethernet Module, TCP/IP to serial, POE Function Converter RS232/485/422 to Ethernet RJ45 has been designed for the industrial environment. It combines multiple functions including serial server, Modbus gateway, MQTT gateway, RS485 to JSON, etc. The module has an RS232/485/422 and Ethernet port (PoE function).Suitable for applications such as data acquisition, IoT gateway, IoT security. and smart device monitoring. Code WV015 ✗ Out-of-Stock Price €32.64
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €4.29
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €5.45
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.26
SparkFun FTDI Basic Breakout - 3.3V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP024 Available Price €16.52
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.06
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
6-pin/10-pin Kanda DIL adapter 6-pin/10-pin Kanda DIL adapter features: - Connector for Usbasp Programmer AVR Atmega8 Atmega128 Code B0051 Available Price €1.07
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.39